manualshive.com logo in svg

Toyota 1996 LAND CRUISER, User Manual

Get your hands on the user manual for the powerful Toyota 1996 LAND CRUISER for free download. This manual is essential for understanding the ins and outs of this iconic vehicle. Download it now from manualshive.com and take your driving experience to the next level.

Share
Download
background image

AT0T5

−

02

AT1366

AT2000

AT2001

AT

−

10

−

AUTOMATIC TRANSMISSION

PARKING LOCK PAWL

794

Author:

Date:

1996 LAND CRUISER   (RM451U)

PARKING LOCK PAWL

ON

−

VEHICLE REPAIR

1.

REMOVE VALVE BODY (See page 

AT

−

7

)

2.

REMOVE PARKING LOCK PAWL BRACKET

3.

REMOVE SPRING FROM PARKING LOCK PAWL
SHAFT

4.

REMOVE PARKING LOCK PAWL AND SHAFT

5.

REINSTALL PARKING LOCK PAWL AND SHAFT

6.

REINSTALL SPRING

7.

REINSTALL PARKING LOCK PAWL BRACKET

HINT:

S

Push the lock rod fully forward.

S

Check that the parking lock pawl operates smoothly.

Torque: 7.4 N·m (75 kgf·cm, 65 in.·lbf)

8.

REINSTALL VALVE BODY (See page 

AT

−

7

)

Brought to you by BirfMark

Brought to you by BirfMark 
 Version 1.00 - 12/21/2010

Summary of Contents for 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 1996 LAND CRUISER

Yakima K1188 Instructions Manual preview
K1188
Brand: Yakima Pages: 12
JEHNERT SOUND DESIGN 65400 Assembly Instruction Manual preview
65400
Brand: JEHNERT SOUND DESIGN Pages: 8
Rainbow Experience Series Installation Manual preview
Experience Series
Brand: Rainbow Pages: 19
Yakima K1006 Instructions Manual preview
K1006
Brand: Yakima Pages: 12
Whispbar K611W Fitting Instructions Manual preview
K611W
Brand: Whispbar Pages: 77
tams elektronik 54-01016 Manual preview
54-01016
Brand: tams elektronik Pages: 44
Fab Fours VI-COWL Installation Instructions Manual preview
VI-COWL
Brand: Fab Fours Pages: 19
Hummer HX-T Owner'S Manual preview
HX-T
Brand: Hummer Pages: 31
Calix M5T 204 Assembly Instructions preview
M5T 204
Brand: Calix Pages: 4
SSV Works RG4-DM3 Manual preview
RG4-DM3
Brand: SSV Works Pages: 2
AUTOTECH 10.109.418K Installation Instructions preview
10.109.418K
Brand: AUTOTECH Pages: 4
Scion 2013 iQ Warranty & Maintenance Manual preview
2013 iQ
Brand: Scion Pages: 58
RADICAL R-C10AD2 Device Installation Manual preview
R-C10AD2
Brand: RADICAL Pages: 11
Truma Mover S Installation & Operation Instructions preview
Mover S
Brand: Truma Pages: 16
National Cycle Quantum Wash'n'Wipe N30205 Assembly Instructions And Owner'S Manual preview
Quantum Wash'n'Wipe N30205
Brand: National Cycle Pages: 12
Mercedes-Benz A-Class 2020 Operator'S Manual preview
A-Class 2020
Brand: Mercedes-Benz Pages: 434
VDO TRIM GAUGE Installation Instructions Manual preview
TRIM GAUGE
Brand: VDO Pages: 6
DV8 FBBR-04 Installation Manual preview
FBBR-04
Brand: DV8 Pages: 14

Brands by name

Popular brands

Load more brands