manualshive.com logo in svg

Toyota 1996 LAND CRUISER, User Manual, Page: 1097 / 1381

Share
Download
Toyota 1996 LAND CRUISER User Manual Download Page 1097

SA1UO

−

01

SA2419

SST

SA2418

SST

−

SUSPENSION AND AXLE

FRONT DIFFERENTIAL CARRIER

SA

−

35

1996 LAND CRUISER   (RM451U)

REPLACEMENT

1.

REMOVE DUST DEFLECTOR TO COMPANION
FLANGE

Using SST and a press, remove the dust deflector.

SST

09950

−

00020

2.

INSTALL DUST DEFLECTOR TO COMPANION
FLANGE

Using SST and a press, install a new dust deflector.

SST

09726

−

40010

Brought to you by BirfMark

Brought to you by BirfMark 
 Version 1.00 - 12/21/2010

Summary of Contents for 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments