manualshive.com logo in svg

Toyota 1996 LAND CRUISER, User Manual, Page: 531 / 1381

Share
Download
Toyota 1996 LAND CRUISER User Manual Download Page 531

BE6653

A00499

A00488

Throttle Position Sensor

4

3

2

1

1

11

9

10

E5

E5

E5

E5

VTA

ECM

VCC

IDL1

E2

E1

12V

5V

ON

BE6653
A00496

A00498

A00489

4

3

2
1

1

11

9

10

E5

E5

E5

E5

VTA1

ECM

VCC

IDL1
E2

12V

5V

ON

Throttle Position
Sensor

E5 Connector

−

DIAGNOSTICS

ENGINE

DI

−

95

1996 LAND CRUISER   (RM451U)

4

Check for short in harness or ECM.

PREPARATION:

(a)

Disconnect throttle position sensor connector.

(b)

Turn ignition switch ON.

CHECK:

Read CTP switch signal on TOYOTA hand

−

held tester.

OK:

CTP switch signal: OFF

OK

Confirm good connection at sensor.

If OK, replace throttle position sensor.

NG

5

Check for short in harness or ECM.

PREPARATION:

(a)

Remove instrument panel speaker No.1 panel
(See page 

SF

−

65

).

(b)

Disconnect E5 connector of ECM.

HINT:
Throttle position sensor connector is disconnected.
(c)

Turn ignition switch ON.

CHECK:

Read CTP switch signal on TOYOTA hand

−

held tester.

OK:

CTP switch signal: OFF

OK

Short in harness between ECM and throttle

position sensor, repair or replace harness.

NG

Confirm connection at ECM.

If OK, replace ECM (See page 

IN

−

28

).

Brought to you by BirfMark

Brought to you by BirfMark 
 Version 1.00 - 12/21/2010

Summary of Contents for 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments