Toyota 1996 LAND CRUISER User Manual Download Page 1280

Page: 1280 / 1381

R12473

SR168

−

SR0097

−

STEERING

STEERING WHEEL

−

1058

Author:

Date:

1996 LAND CRUISER (RM451U)

STEERING WHEEL

INSPECTION

CHECK STEERING WHEEL FREEPLAY

(a)

With the vehicle stopped and tires pointed straight ahead,
rock the steering wheel gently back and forth with light fin-
ger pressure.

(b)

Freeplay should not exceed the maximum.

Maximum freeplay: 40 mm (1.58 in.)

If the freeplay exceeds the maximum, adjust it in the following
procedure.

ADJUST STEERING GEAR

(a)

Point the front wheels straight ahead.

(b)

Loosen the adjusting screw lock nut.

(c)

Turn the cross shaft adjusting screw clockwise to de-
crease steering wheel freeplay and counterclockwise to
increase it.

HINT:
Turn the adjusting screw in small increments and check the
freeplay between each adjustment.
(d)

Turn the steering wheel half way around in both direc-
tions.

(e)

Check that the freeplay is correct and steering is smooth
and without rough spots.

(f)

Torque the adjusting screw lock nut (See page

−

CHECK STEERING EFFORT

(a)

Center the steering wheel.

(b)

Remove the steering wheel pad (See page

−

(c)

Start the engine and run it at idle.

(d)

Measure the steering effort in both directions.

Reference: 8.3 N·m (85 kgf·cm, 73 in.·lbf)

Brought to you by BirfMark

Brought to you by BirfMark
Version 1.00 - 12/21/2010

«
...
1278
1279
1280
1281
1282
...
»

Summary of Contents for 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 1996 LAND CRUISER

Reviews:

Related manuals for 1996 LAND CRUISER

Brands by name

Popular brands

Toyota 1996 LAND CRUISER, User Manual

Search results

Summary of Contents for 1996 LAND CRUISER

Reviews:

Related manuals for 1996 LAND CRUISER

Brands by name

Popular brands