Toyota 1996 LAND CRUISER User Manual Download Page 419

Page: 419 / 1381

−

CHARGING

GENERATOR

1996 LAND CRUISER (RM451U)

INSTALL BRUSH HOLDER

(a)

Install the brush holder on the rectifier end frame with the
2 screws.

NOTICE:
Be careful of the holder installation direction.

Torque: 2.0 N·m (20 kgf·cm, 17 in.·lbf)

(b)

Place the brush holder cover on the brush holder.

INSTALL REAR END COVER

(a)

Install the end cover together with the rectifier plate.
(1)

Hand tighten the bolt first for positioning the plate.

(2)

Tighten the 3 nuts and bolt.

Torque:
Bolt: 3.8 N·m (39 kgf·cm, 34 in.·lbf)
Nut: 4.4 N·m (45 kgf·cm, 39 in.·lbf)

(b)

Install the terminal insulator with the nut.

Torque: 4.1 N·m (42 kgf·cm, 36 in.·lbf)

CHECK THAT ROTOR ROTATES SMOOTHLY

Brought to you by BirfMark

Brought to you by BirfMark
Version 1.00 - 12/21/2010

Summary of Contents for 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 1996 LAND CRUISER

Reviews:

Related manuals for 1996 LAND CRUISER

Brands by name

Popular brands

Toyota 1996 LAND CRUISER, User Manual

Search results

Summary of Contents for 1996 LAND CRUISER

Reviews:

Related manuals for 1996 LAND CRUISER

Brands by name

Popular brands