Toyota 1996 LAND CRUISER User Manual Download Page 924

Page: 924 / 1381

LU0KK

−

LUBRICATION

OIL COOLER

1996 LAND CRUISER (RM451U)

REMOVAL

DRAIN ENGINE COOLANT

REMOVE AIR CLEANER CAP AND HOSE

REMOVE FRONT EXHAUST PIPE

(a)

Disconnect the heated oxygen sensor connector.

(b)

Remove the 2 nuts and 2 bolts holding the front exhaust
pipe to the rear TWC.

(c)

Disconnect the front exhaust pipe, and remove the gas-
ket.

(d)

Loosen the clamp bolt and disconnect the clamp from the
No.1 support bracket.

(e)

Remove the 2 bolts and No.1 support bracket.

(f)

Remove the 4 nuts, front exhaust pipe and 2 gaskets.

REMOVE NO.1 EXHAUST MANIFOLD

(a)

Remove the 3 bolts and No.1 heat insulator.

(b)

Remove the 6 nuts, exhaust manifold and gasket.

Brought to you by BirfMark

Brought to you by BirfMark
Version 1.00 - 12/21/2010

Summary of Contents for 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 1996 LAND CRUISER

Reviews:

Related manuals for 1996 LAND CRUISER

Brands by name

Popular brands

Toyota 1996 LAND CRUISER, User Manual

Search results

Summary of Contents for 1996 LAND CRUISER

Reviews:

Related manuals for 1996 LAND CRUISER

Brands by name

Popular brands