Toyota 1996 LAND CRUISER User Manual Download Page 507

Page: 507 / 1381

A00168

EGR Gas Temp.

Sensor

ECM

BE6653

FI7055

THG

−

DIAGNOSTICS

ENGINE

−

1996 LAND CRUISER (RM451U)

INSPECTION PROCEDURE
TOYOTA hand

−

held tester

Connect the TOYOTA hand

−

held tester and read value of EGR gas temp. value.

PREPARATION:

(a)

Remove the fuse cover on the instrument panel.

(b)

Connect the TOYOTA hand

−

held tester to the DLC3.

(c)

Turn ignition switch ON and push the TOYOTA hand

−

held tester main switch ON.

CHECK:

Read EGR gas temp. on the TOYOTA hand

−

held tester.

OK:

EGR gas temp.: 10

C (50

F) or more

HINT:
If there is and open circuit, the TOYOTA hand

−

held tester indicates 3.1

C (37.6

F).

Go to step 4.

Check for open in harness or ECM.

PREPARATION:

(a)

Disconnect the EGR gas temp. sensor connector.

(b)

Connect sensor wire harness terminals together.

(c)

Turn ignition switch ON.

CHECK:

Read EGR gas temp. on the TOYOTA hand

−

held tester.

OK:

EGR gas temp.: Approx. 157.5

C (315.5

Confirm good connection at sensor.

If OK, replace EGR gas temp. sensor.

Brought to you by BirfMark

Brought to you by BirfMark
Version 1.00 - 12/21/2010

Summary of Contents for 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 1996 LAND CRUISER

Reviews:

Related manuals for 1996 LAND CRUISER

Brands by name

Popular brands

Toyota 1996 LAND CRUISER, User Manual

Search results

Summary of Contents for 1996 LAND CRUISER

Reviews:

Related manuals for 1996 LAND CRUISER

Brands by name

Popular brands