manualshive.com logo in svg

Toyota 1996 LAND CRUISER, User Manual, Page: 607 / 1381

Share
Download
Toyota 1996 LAND CRUISER User Manual Download Page 607

Q07657

D00109

−

DIAGNOSTICS

AUTOMATIC TRANSMISSION

DI

−

171

1996 LAND CRUISER   (RM451U)

2

Check park/neutral position switch.

PREPARATION:

(a)

Jack up the vehicle.

(b)

Remove the park/neutral position switch connector.

CHECK:

Check the continuity between each terminal shown below when
the shift lever is moved to each position.

OK:

Shift Position

Terminal No. to continuity

Terminal No. to continuity

P

4 

−

 7

5 

−

 6

R

4 

−

 8

−

N

4 

−

 10

5 

−

 6

D

4 

−

 9

−

2

2 

−

 4

−

L

3 

−

 4

−

NG

Replace park/neutral position switch.

OK

Repair or replace harness and connector between battery and park/neutral position switch, and

park/neutral position switch and ECM (See page 

IN

−

28

).

Brought to you by BirfMark

Brought to you by BirfMark 
 Version 1.00 - 12/21/2010

Summary of Contents for 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments