Toyota 1996 LAND CRUISER User Manual Download Page 164

Page: 164 / 1381

BE1M4

−

BE1428

OFF

−

BODY ELECTRICAL

INTERIOR LIGHT SYSTEM

−

1996 LAND CRUISER (RM451U)

INSPECTION

INSPECT GLOVE BOX LIGHT SWITCH CONTINUITY

Switch position

Tester connection

Specified condition

OFF (Closed)

−

No continuity

ON (Opened)

−

Continuity

If continuity is not as specified, replace the switch.

INSPECT DOOR COURTESY SWITCH CONTINUITY

(a)

Check that there is continuity between terminal and the
switch body with the switch ON (switch pin released:
opened door).

(b)

Check that there is no continuity between terminal and
the switch body with the switch OFF (switch pin pushed
in: closed door).

If operation is not as specified, replace the switch.

INSPECT FRONT PERSONAL LIGHT CONTINUITY

Switch position

Tester connection

Specified condition

OFF

−

No continuity

−

Continuity

If continuity is not as specified, replace the personal light.

INSPECT ROOM LIGHT ASSEMBLY

(a)

Disconnect the connector from room light assembly.

(b)

Turn the room light switch ON, check that there is continu-
ity between terminal 2 and body ground.

(c)

Turn the room light switch DOOR, and check that there is
continuity between terminal 1 and 2.

If operation is not as specified, replace the switch.

Brought to you by BirfMark

Brought to you by BirfMark
Version 1.00 - 12/21/2010

Summary of Contents for 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 1996 LAND CRUISER

Reviews:

Related manuals for 1996 LAND CRUISER

Brands by name

Popular brands

Toyota 1996 LAND CRUISER, User Manual

Search results

Summary of Contents for 1996 LAND CRUISER

Reviews:

Related manuals for 1996 LAND CRUISER

Brands by name

Popular brands