Toyota 1996 LAND CRUISER User Manual Download Page 415

Page: 415 / 1381

CH0HQ

−

P22368

SST

P22369

SST

N00581

SST

−

CHARGING

GENERATOR

1996 LAND CRUISER (RM451U)

REPLACEMENT

REPLACE FRONT BEARING

(a)

Remove the 4 screws and bearing retainer.

(b)

Using SST and a press, press out the bearing.
SST

09950

−

60010 (09951

−

00260, 09952

−

06010)

(c)

Using SST and a press, press in a new bearing.
SST

09950

−

60010 (09951

−

00500)

(d)

Install the bearing retainer with the 4 screws.

Torque: 2.6 N·m (27 kgf·cm, 23 in.·lbf)

REPLACE REAR BEARING

(a)

Using SST, remove the bearing cover (outside) and bear-
ing.
SST

09820

−

00021

NOTICE:
Be careful not to damage the fan.

(b)

Remove the bearing cover (inside).

Brought to you by BirfMark

Brought to you by BirfMark
Version 1.00 - 12/21/2010

Summary of Contents for 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 1996 LAND CRUISER

Reviews:

Toyota 1996 LAND CRUISER, User Manual, Page: 415 / 1381

Search results

Summary of Contents for 1996 LAND CRUISER

Reviews: