manualshive.com logo in svg

Toyota 1996 LAND CRUISER, User Manual

Get your hands on the user manual for the powerful Toyota 1996 LAND CRUISER for free download. This manual is essential for understanding the ins and outs of this iconic vehicle. Download it now from manualshive.com and take your driving experience to the next level.

Share
Download
background image

DI

−

222

−

DIAGNOSTICS

ANTI

−

LOCK BRAKE SYSTEM

1996 LAND CRUISER   (RM451U)

2

Is DTC output?

Check DTC on page 

DI

−

190

.

NO

Normal.

YES

3

Check that CENTER DIFF. LOCK indicator light does not go off.

NO

Go to step 6.

YES

4

Check that bulb for CENTER DIFF. LOCK indicator light is not burnt out.

YES

Replace indicator light.

NO

5

Check for open in harness and connector between battery and CENTER DIFF.

LOCK indicator light, and CENTER DIFF. LOCK indicator light and ABS ECU (See

page 

IN

−

28

).

NG

Repair or replace harness or connector.

OK

Brought to you by BirfMark

Brought to you by BirfMark 
 Version 1.00 - 12/21/2010

Summary of Contents for 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 1996 LAND CRUISER

PAC RadioPRO 5 RP5-GM41 Quick Start Manual preview
RadioPRO 5 RP5-GM41
Brand: PAC Pages: 3
Parrot CK3300 Setup Information Manual preview
CK3300
Brand: Parrot Pages: 19
Parrot Minikit+ Quick Start Manual preview
Minikit+
Brand: Parrot Pages: 88
Parrot Minikit+ Information Sheet preview
Minikit+
Brand: Parrot Pages: 2
Parrot CK3100 LCD Specifications preview
CK3100 LCD
Brand: Parrot Pages: 2
Parrot CK 3000 Evolution Installation Notes preview
CK 3000 Evolution
Brand: Parrot Pages: 8
Parrot CK 3000 Evolution User Manual preview
CK 3000 Evolution
Brand: Parrot Pages: 106
OCTO SmartDiag2GO GD201-O User Manual preview
SmartDiag2GO GD201-O
Brand: OCTO Pages: 5
GATmatic TWC-562S Installation, Operation & Maintenance Manual preview
TWC-562S
Brand: GATmatic Pages: 13
TATA Motors tigor Owner'S Manual preview
tigor
Brand: TATA Motors Pages: 159
FALCON RIDGE HO-P500-FC04 Instructions For Installation And Care preview
HO-P500-FC04
Brand: FALCON RIDGE Pages: 8
Scosche 142HUD2 Manual preview
142HUD2
Brand: Scosche Pages: 8
P-Invent Troller User Manual preview
Troller
Brand: P-Invent Pages: 4
Whispbar K951W Fitting Instructions For Basic Carrier preview
K951W
Brand: Whispbar Pages: 15
Bestop 51252 Installation Instructions preview
51252
Brand: Bestop Pages: 4
Vauxhall 2013 Ampera Infotainment Manual preview
2013 Ampera
Brand: Vauxhall Pages: 95
Edelbrock 460 Ford Installation Instructions preview
460 Ford
Brand: Edelbrock Pages: 2
Nos 05183NOS Owner'S Manual preview
05183NOS
Brand: Nos Pages: 22

Brands by name

Popular brands

Load more brands