manualshive.com logo in svg

Toyota 1996 LAND CRUISER, User Manual

Get your hands on the user manual for the powerful Toyota 1996 LAND CRUISER for free download. This manual is essential for understanding the ins and outs of this iconic vehicle. Download it now from manualshive.com and take your driving experience to the next level.

Share
Download
background image

BO37K

−

01

BO5366

Piston Rod

Cylinder

Hole Here

10 

−

 20 mm

(0.39 

−

 0.99 in.)

−

BODY

HOOD SUPPORT

BO

−

7

1241

Author:

Date:

1996 LAND CRUISER   (RM451U)

REPLACEMENT

1.

REMOVE DAMPER STAY FROM HOOD

Remove the 2 bolts and support from the hood.
HINT:
While supporting the hood with your hand, remove the hood.

2.

REMOVE DAMPER STAY FROM BODY

Remove the 2 bolts and support.

3.

REPLACE DAMPER STAY

NOTICE:

S

Do not disassemble the damper stay because the cyl-
inder is filled with pressurized gas.

S

If the damper stay is to be replaced, drill a 2.0 

−

 3.0 mm

(0.079 

−

 0.118 in.) hole as shown in the illustration to

completely release the high

−

pressure gas before dis-

posing of it.

S

When drilling, chips may fly out so work carefully.

S

The gas is colorless, odorless and non

−

toxic.

S

When working, handle the damper stay carefully.
Never score or scratch the exposed part of the piston
rod, and never allow paint or oil to get on it.

S

Do not turn the piston rod and cylinder with the damp-
er stay fully extended.

4.

INSTALL DAMPER STAY

Install the damper stay.

Brought to you by BirfMark

Brought to you by BirfMark 
 Version 1.00 - 12/21/2010

Summary of Contents for 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 1996 LAND CRUISER

Parrot CK 3000 Evolution Specifications preview
CK 3000 Evolution
Brand: Parrot Pages: 2
APEXi V-AFC II Instruction Manual preview
V-AFC II
Brand: APEXi Pages: 18
Prorack K519 Fitting Instructions For Basic Carrier preview
K519
Brand: Prorack Pages: 15
Mobile Create MCM3 Instruction Manual preview
MCM3
Brand: Mobile Create Pages: 15
Sirius Satellite Radio Streamer GTR Installation Manual preview
Streamer GTR
Brand: Sirius Satellite Radio Pages: 8
WABCO TP19108 Installation Manual preview
TP19108
Brand: WABCO Pages: 32
Mazda 1989 323 Manual preview
1989 323
Brand: Mazda Pages: 13
Fab Fours F2950 Installation Instructions Manual preview
F2950
Brand: Fab Fours Pages: 21
Volvo S90 2018 Quick Manual preview
S90 2018
Brand: Volvo Pages: 42
FVC Sprinter Side Ladder Installation Manual preview
Sprinter Side Ladder
Brand: FVC Pages: 8
Thule RaceWay 991 Instructions Manual preview
RaceWay 991
Brand: Thule Pages: 12
Yakima K896 Instructions Manual preview
K896
Brand: Yakima Pages: 12
RAM Truck 2014 Owner'S Manual preview
Truck 2014
Brand: RAM Pages: 330
Thule Kit 1312 Instructions Manual preview
Kit 1312
Brand: Thule Pages: 8
Xingyun XY40EV Service Manual preview
XY40EV
Brand: Xingyun Pages: 74
Toyota Solara guide Owner'S Manual preview
Solara guide
Brand: Toyota Pages: 497
CITROËN Jumpy Miltispace Owner'S Handbook Manual preview
Jumpy Miltispace
Brand: CITROËN Pages: 164
Directed MIT4 Firmware Specific Manual preview
MIT4
Brand: Directed Pages: 30

Brands by name

Popular brands

Load more brands