manualshive.com logo in svg

Toyota 1996 LAND CRUISER, User Manual

Get your hands on the user manual for the powerful Toyota 1996 LAND CRUISER for free download. This manual is essential for understanding the ins and outs of this iconic vehicle. Download it now from manualshive.com and take your driving experience to the next level.

Share
Download
background image

SF0PO

−

09

Z02917

Ohmmeter

TEMPERATURE 

°

C (

°

F)

RESIST

ANCE k

Ω

Acceptable

−

SFI

ENGINE COOLANT TEMPERATURE (ECT) SENSOR

SF

−

61

689

Author:

Date:

1996 LAND CRUISER   (RM451U)

ENGINE COOLANT
TEMPERATURE (ECT) SENSOR

INSPECTION

1.

DRAIN ENGINE COOLANT

2.

REMOVE ECT SENSOR

(a)

Disconnect the ECT sensor connector.

(b)

Using a 19 mm deep socket wrench, remove the ECT
sensor and gasket.

3.

INSPECT ECT SENSOR

Using an ohmmeter, measure the resistance between the ter-
minals.

Resistance: Refer to the chart graph

If the resistance is not as specified, replace the ECT sensor.

4.

REINSTALL ECT SENSOR

(a)

Using a 19 mm deep socket wrench, install the ECT sen-
sor and gasket.

Torque: 24.5 N·m (250 kgf·cm, 17.5 ft·lbf)

(b)

Connect the ECT sensor connector.

5.

REFILL ENGINE COOLANT

Brought to you by BirfMark

Brought to you by BirfMark 
 Version 1.00 - 12/21/2010

Summary of Contents for 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 1996 LAND CRUISER

Prorack K383 Fitting Instructions Manual preview
K383
Brand: Prorack Pages: 14
Club Car Gasoline/Electric DS Golf Car 1996 Owner'S Manual preview
Gasoline/Electric DS Golf Car 1996
Brand: Club Car Pages: 48
Mazda 2 2016 Owner'S Manual preview
2 2016
Brand: Mazda Pages: 720
Globalsat MR-350P Installation Manual preview
MR-350P
Brand: Globalsat Pages: 2
Whispbar K448W Fitting Instructions Manual preview
K448W
Brand: Whispbar Pages: 15
Maserati Gransport Owner'S Manual preview
Gransport
Brand: Maserati Pages: 210
OnStar liveon Owner'S Manual preview
liveon
Brand: OnStar Pages: 22
Fast Master Products SWIVELWHEEL-46 Assembly Instructions Manual preview
SWIVELWHEEL-46
Brand: Fast Master Products Pages: 13
BrandMotion FLTW-7511 Installation Manual preview
FLTW-7511
Brand: BrandMotion Pages: 6
Navman T1 F20 User Manual preview
T1 F20
Brand: Navman Pages: 10
Macrom EF-AR1-5561 Manual preview
EF-AR1-5561
Brand: Macrom Pages: 10
Prime Design URX-001-E Assembly Instructions Manual preview
URX-001-E
Brand: Prime Design Pages: 8
Curt Group Aries AL235045 Installation Manual preview
Aries AL235045
Brand: Curt Group Pages: 2
Fleetwood Bounder turbo diesel 2001 Instructions Manual preview
Bounder turbo diesel 2001
Brand: Fleetwood Pages: 166
Saab 9-3 M03- Installation Instructions Manual preview
9-3 M03-
Brand: Saab Pages: 16
Vauxhall Antara 2014 Owner'S Manual preview
Antara 2014
Brand: Vauxhall Pages: 215
OCAM SS2-RANGER-12 Fitting Instruction preview
SS2-RANGER-12
Brand: OCAM Pages: 4
Whelen Engineering Company SAK5 Installation Manual preview
SAK5
Brand: Whelen Engineering Company Pages: 2

Brands by name

Popular brands

Load more brands