Toyota 1996 LAND CRUISER User Manual Download Page 1095

Page: 1095 / 1381

Z15178

Matchmarks

SA2464

W03472

SST

RA0997

FA2046

Matchmarks

−

SUSPENSION AND AXLE

FRONT DIFFERENTIAL CARRIER

−

1996 LAND CRUISER (RM451U)

18. REMOVE RING GEAR

(a)

Using a screwdriver and hammer, unstake the lock plate.

(b)

Place matchmarks on the ring gear and differential case.

(c)

Remove the ring gear 10 set bolts and 5 lock plates.

(d)

Using a plastic hammer, tap on the ring gear to separate
it from the differential case.

19. CHECK DIFFERENTIAL CASE RUNOUT

(a)

Install the differential case in the differential carrier and
tighten the adjusting nut just to where there is no play in
the bearing.

(b)

Using a dial indicator, measure the differential case run-
out.

Maximum case runout: 0.07 mm (0.0028 in.)

(c)

Remove the differential case.

20. REMOVE SIDE BEARING FROM DIFFERENTIAL

CASE

Using SST, pull the side bearing from the differential case.

SST

09950

−

40010 (09951

−

04010, 09952

−

04020,

09953

−

04020, 09954

−

04010, 09955

−

04010,

09957

−

04010, 09958

−

04010),

09950

−

60010 (09951

−

00480)

HINT:
Fix the claws of SST to the notches in the differential case.

21. w/o DIFFERENTIAL LOCK:

DISASSEMBLE DIFFERENTIAL CASE

(a)

Using a pin punch and hammer, remove the straight pin.

(b)

Remove these parts from the differential case:

Pinion shaft

2 Pinion gears

2 Pinion gear thrust washers

2 Side gears

2 Side gear thrust washers

22. w/ DIFFERENTIAL LOCK:

DISASSEMBLE DIFFERENTIAL CASE

(a)

Place matchmarks on the LH and RH cases.

(b)

Remove the 8 bolts uniformly, a little at a time.

(c)

Using a plastic hammer, separate the LH and RH cases.

(d)

Remove these parts from the RH differential case:

2 Side gears

2 Side gear thrust washers

Spider

Brought to you by BirfMark

Brought to you by BirfMark
Version 1.00 - 12/21/2010

«
...
1093
1094
1095
1096
1097
...
»

Summary of Contents for 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 1996 LAND CRUISER

Reviews:

Related manuals for 1996 LAND CRUISER

Brands by name

Popular brands

Toyota 1996 LAND CRUISER, User Manual

Search results

Summary of Contents for 1996 LAND CRUISER

Reviews:

Related manuals for 1996 LAND CRUISER

Brands by name

Popular brands