manualshive.com logo in svg

Toyota 1996 LAND CRUISER, User Manual, Page: 1057 / 1381

Share
Download
Toyota 1996 LAND CRUISER User Manual Download Page 1057

RS0PH

−

01

RS

−

34

−

SUPPLEMENTAL RESTRAINT SYSTEM

AIRBAG SENSOR ASSEMBLY

1996 LAND CRUISER   (RM451U)

INSPECTION

1.

VEHICLE NOT INVOLVED IN COLLISION

Do a diagnostic system check. (See page 

DI

−

240

)

2.

VEHICLE INVOLVED IN COLLISION AND AIRBAG IS NOT DEPLOYED

Do a diagnostic system check. (See page 

DI

−

240

)

3.

VEHICLE INVOLVED IN COLLISION AND AIRBAG IS DEPLOYED

Replace the airbag sensor assembly. (See page 

RS

−

32

)

Brought to you by BirfMark

Brought to you by BirfMark 
 Version 1.00 - 12/21/2010

Summary of Contents for 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments