manualshive.com logo in svg

Toyota 1996 LAND CRUISER, User Manual, Page: 1360 / 1381

Share
Download
Toyota 1996 LAND CRUISER User Manual Download Page 1360

TR0BA

−

01

TF0893

SST

Q00538

TF0896

SST

−

TRANSFER

IDLER GEAR

TR

−

17

1996 LAND CRUISER   (RM451U)

REASSEMBLY

HINT:
Coat all of the sliding and rotating surfaces with gear oil before
assembly.

1.

INSTALL FRONT TAPER ROLLER BEARING

Using SST and a press, install the front taper roller bearing.

SST

09316

−

60011 (09316

−

00011, 09316

−

00031)

2.

INSTALL HIGH AND LOW CLUTCH SLEEVE

HINT:
Make sure to install the high and low clutch sleeve in the correct
direction.

3.

INSTALL NEEDLE ROLLER BEARING AND IDLER
LOW GEAR TO IDLER GEAR

(a)

Apply gear oil to the needle roller bearing.

(b)

Install the needle roller bearing and idler low gear.

4.

INSTALL REAR TAPER ROLLER BEARING

Using SST and a press, install the rear taper roller bearing.

SST

09316

−

60011 (09316

−

00011, 09316

−

00071)

5.

INSPECT IDLER LOW GEAR RADIAL AND THRUST
CLEARANCE
(See page 

TR

−

16

)

Brought to you by BirfMark

Brought to you by BirfMark 
 Version 1.00 - 12/21/2010

Summary of Contents for 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments