Toyota 1996 LAND CRUISER User Manual Download Page 803

Page: 803 / 1381

EM1EB

−

ENGINE MECHANICAL

TIMING CHAIN

−

1996 LAND CRUISER (RM451U)

INSTALLATION

SET CRANKSHAFT

Turn the crankshaft until the set key on crankshaft facing down-
ward.

INSTALL PUMP DRIVE SHAFT GEAR

INSTALL OIL PUMP DRIVE SHAFT GEAR

(a)

Apply a light coat of engine oil on the shaft portion of the
gear.

(b)

Install the gear.

INSTALL CRANKSHAFT ROTOR

INSTALL OIL JET

Install the oil jet with the bolt.

Torque: 20 N·m (200 kgf·cm, 14 ft·lbf)

INSTALL CHAIN TENSIONER SLIPPER AND VIBRA-
TION DAMPER

(a)

Install the damper with the 2 bolts.

Torque: 20 N·m (200 kgf·cm, 14 ft·lbf)

(b)

Using a 10 mm hexagon wrench, install the slipper with
the bolt.

Torque: 69 N·m (700 kgf·cm, 51 ft·lbf)

Brought to you by BirfMark

Brought to you by BirfMark
Version 1.00 - 12/21/2010

Summary of Contents for 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 1996 LAND CRUISER

Reviews:

Toyota 1996 LAND CRUISER, User Manual, Page: 803 / 1381

Search results

Summary of Contents for 1996 LAND CRUISER

Reviews: