manualshive.com logo in svg

Toyota 1996 LAND CRUISER, User Manual

Get your hands on the user manual for the powerful Toyota 1996 LAND CRUISER for free download. This manual is essential for understanding the ins and outs of this iconic vehicle. Download it now from manualshive.com and take your driving experience to the next level.

Share
Download
background image

LU0KG

−

02

−

LUBRICATION

OIL PUMP

LU

−

5

1996 LAND CRUISER   (RM451U)

REMOVAL

HINT:
When repairing the oil pump, the oil pan and strainer should be
removed and cleaned.

1.

DRAIN ENGINE OIL

2.

REMOVE ENGINE UNDER COVER

3.

DRAIN ENGINE COOLANT

4.

REMOVE RADIATOR (See page 

CO

−

14

)

5.

DISCONNECT A/C COMPRESSOR AND BRACKET

(a)

Loosen the idler pulley nut and adjusting bolt, and remove
the drive belt.

(b)

Remove the 4 mounting bolts, and disconnect the com-
pressor from the bracket.

HINT:
Put aside the compressor, and suspend it.
(c)

Remove the 5 bolts and A/C compressor bracket.

6.

REMOVE RADIATOR PIPE

(a)

Disconnect the No.2 radiator hose from the water inlet.

(b)

Remove the 2 nuts and radiator pipe.

7.

REMOVE WATER PUMP

Remove the 4 bolts, 2 nuts, water pump and gasket.

8.

REMOVE CYLINDER HEAD (See page 

EM

−

28

)

9.

DISCONNECT OIL COOLER PIPE BRACKET FROM
NO.1 OIL PAN

Brought to you by BirfMark

Brought to you by BirfMark 
 Version 1.00 - 12/21/2010

Summary of Contents for 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 1996 LAND CRUISER

HALE MM-03 Driver Manual preview
MM-03
Brand: HALE Pages: 44
Audiovox Prestige APS-45B Installation Manual preview
Prestige APS-45B
Brand: Audiovox Pages: 8
Volvo 1985 740 GL Owner'S Manual preview
1985 740 GL
Brand: Volvo Pages: 138
muth signal mirror 2005-2009 Ford Mustang Installation Instruction preview
signal mirror 2005-2009 Ford Mustang
Brand: muth Pages: 9
Waeco MagicWatch MWE250 Installation And Operating Manual preview
MagicWatch MWE250
Brand: Waeco Pages: 172
Dodge 8W-30 Wiring Diagram preview
8W-30
Brand: Dodge Pages: 24
Cadillac 1993 Seville Owners Literature preview
1993 Seville
Brand: Cadillac Pages: 407
Harman Kardon DP 2US Quick Start Manual preview
DP 2US
Brand: Harman Kardon Pages: 16
TATA Motors TIAGO XZ 2019 Owner'S Manual preview
TIAGO XZ 2019
Brand: TATA Motors Pages: 184
B&G electronics PW-50C Civilian Installation And Operation Manual preview
PW-50C Civilian
Brand: B&G electronics Pages: 7
Icom RMK-5 Instruction Manual preview
RMK-5
Brand: Icom Pages: 20
Easee Home Wallbox Installation Instructions Manual preview
Home Wallbox
Brand: Easee Pages: 12
Ford Mustang 2007 Supplement Manual preview
Mustang 2007
Brand: Ford Pages: 40
RAM 1500 CLASSIC 2020 Owner'S Manual preview
1500 CLASSIC 2020
Brand: RAM Pages: 360
Lincoln 2017 MKC Owner'S Manual preview
2017 MKC
Brand: Lincoln Pages: 538
chinavasion CVTM-C163 User Manual preview
CVTM-C163
Brand: chinavasion Pages: 3
PEUGEOT 208 T16 User Manual preview
208 T16
Brand: PEUGEOT Pages: 67
FALCON RIDGE CF-U-1000-RW02 Instructions For Installation And Care preview
CF-U-1000-RW02
Brand: FALCON RIDGE Pages: 8

Brands by name

Popular brands

Load more brands