Toyota 1996 LAND CRUISER User Manual Download Page 112

Page: 112 / 1381

AC2722

Connector ”A”

Connector ”B”

AC2723

Connector ”A”

Connector ”B”

AC2722

Connector ”A”

Connector ”B”

AC2723

Connector ”A”

Connector ”B”

−

AIR CONDITIONING

AIR CONDITIONING CONTROL ASSEMBLY

1996 LAND CRUISER (RM451U)

(d)

Then connect the positive (+) lead from the battery to ter-
minal A

−

13 and check that the indicator dims.

If operation is not as specified, replace the A/C control assem-
bly.

Mode Control Switch:
INSPECT INDICATOR LIGHT OPERATION

(a)

Connect the positive (+) lead from the battery to terminal
A

−

9 and the negative (

−

) lead to terminal B

−

16.

(b)

Push each of the mode buttons in and check that their in-
dicator light lights up.

(c)

Then connect the positive (+) lead from the battery to ter-
minal A

−

13 and check that the indicator dims.

If operation is not as specified, replace the A/C control assem-
bly.

Blower Speed Control Switch:
INSPECT INDICATOR LIGHT OPERATION

(a)

Connect the positive (+) lead from the battery to terminal
A

−

9 and the negative (

−

) lead to terminal B

−

16.

(b)

Push each of the blower speed control buttons in and
check that their indicator light lights up.

(c)

Then connect the positive (+) lead from the battery to ter-
minal A

−

13 and check that the indicator dims.

If operation is not as specified, replace the A/C control assem-
bly.

Brought to you by BirfMark

Brought to you by BirfMark
Version 1.00 - 12/21/2010

Summary of Contents for 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 1996 LAND CRUISER

Reviews:

Related manuals for 1996 LAND CRUISER

Brands by name

Popular brands

Toyota 1996 LAND CRUISER, User Manual

Search results

Summary of Contents for 1996 LAND CRUISER

Reviews:

Related manuals for 1996 LAND CRUISER

Brands by name

Popular brands