manualshive.com logo in svg

Toyota 1996 LAND CRUISER, User Manual, Page: 1147 / 1381

Share
Download
Toyota 1996 LAND CRUISER User Manual Download Page 1147

SA2475

SST

−

SUSPENSION AND AXLE

REAR DIFFERENTIAL CARRIER

SA

−

85

1996 LAND CRUISER   (RM451U)

23. w/o DIFFERENTIAL LOCK:

DISASSEMBLE DIFFERENTIAL CASE

(a)

Remove the pinion shaft pin and washer.

(b)

Remove these parts from the differential case:

S

Pinion shaft

S

2 Pinion gears

S

2 Pinion gear thrust washers

S

2 Side gears

S

2 Side gear thrust washers

24. w/ DIFFERENTIAL LOCK:

DISASSEMBLE DIFFERENTIAL CASE

(a)

Place matchmarks on the case and cover.

(b)

Using a torx socket wrench, remove the 5 set bolts and 3
pinion shaft pins.

(c)

Using the 2 cover installation bolts, separate the cover
and case.

(d)

Remove these parts from the differential case:

S

2 Side gears

S

2 Side gear thrust washers

S

4 Pinion gears

S

4 Pinion thrust washers

S

3 Pinion shafts

S

Pinion shaft holder

Brought to you by BirfMark

Brought to you by BirfMark 
 Version 1.00 - 12/21/2010

Summary of Contents for 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments