Toyota 1996 LAND CRUISER User Manual Download Page 722 | Manualshive

Page: 722 / 1381

background image

N14305

N14305

DI-28

9

-

DIAGNOSTICS

CRUISE CONTROL SYSTEM

1996 LAND CRUISER (RM451U)

(d)

Inspect the CANCEL switch.
(1)

Push the main switch ON.

(2)

Drive at a desired speed (40 km/h (25 mph) or high-
er).

(3)

When operating one of the followings, check that
the cruise control system is cancelled and that the
normal driving mode is reset.

Depress the brake pedal

Shift to except D position

Push the main switch OFF

Pull the cruise control switch to CANCEL

(e)

Inspect the RESUME switch.
(1)

Push the main switch ON.

(2)

Drive at a desired speed (40 km/h (25 mph) or high-
er).

(3)

When operating one of the followings, check that
the cruise control system is cancelled and that the
normal driving mode is reset.

Depress the brake pedal

Shift to except D position

Pull the cruise control switch to CANCEL

(4)

After the control switch is turned to RES/ACC at the
driving speed of more than 40 km/h (25 mph), check
that the vehicle restores the speed prior to the can-
cellation.

Brought to you by BirfMark

Brought to you by BirfMark
Version 1.00 - 12/21/2010

«
...
720
721
722
723
724
...
»

Summary of Contents for 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 1996 LAND CRUISER

Brand: ZAPTEC Pages: 240

Brand: Saab Pages: 75

Brand: Yakima Pages: 7

Brand: Yakima Pages: 6

Brand: Yakima Pages: 10

Brand: Yakima Pages: 12

YARIS LIFTBACK 2009

Brand: Toyota Pages: 13

Brand: Westfalia Pages: 71

Brand: AutoWatch Pages: 4

Q Access Alpha GSE 2023

Brand: Q Mobility Group Pages: 9

2010 Civic Sedan

Brand: Honda Pages: 390

Brand: Volvo Pages: 266

Brand: Hyundai Pages: 18

Brand: EUFAB Pages: 16

Brand: Paccar Pages: 63

Brand: TAUBENREUTHER Pages: 18

Brand: INDIWORK Pages: 18

Brand: Opel Pages: 103

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands