manualshive.com logo in svg

Toyota 1996 LAND CRUISER, User Manual

Get your hands on the user manual for the powerful Toyota 1996 LAND CRUISER for free download. This manual is essential for understanding the ins and outs of this iconic vehicle. Download it now from manualshive.com and take your driving experience to the next level.

Share
Download
background image

BE1MS

−

01

BE

−

94

−

BODY ELECTRICAL

ANTENNA

1232

Author:

Date:

1996 LAND CRUISER   (RM451U)

ANTENNA

INSPECTION

1.

w/ MOTOR ANTENNA:
INSPECT ANTENNA SWITCH

Except RADIO

−

LINKED TYPE

Condition

Tester connection

Specified condition

UP Button

Position Free

2 

−

 5

Continuity

UP Button

Position Pushed in

4 

−

 5

Continuity

DOWN Button

Position Free

2 

−

 3

Continuity

DOWN Button

Position Pushed in

3 

−

 4

Continuity

Illumination circuit

1 

−

 6

Continuity

If continuity is not as specified, replace the switch.

2.

INSPECT ANTENNA MOTOR OPERATION

(a)

Connect the positive (+) lead from the battery to terminal
1 and the negative (

−

) lead to terminal 2, and check that

the motor turns (moves upward.)

(b)

Then, reverse the polarity, check that the motor turns the
opposite way (moves downward.)

If operation is not as specified, replace the motor.

Brought to you by BirfMark

Brought to you by BirfMark 
 Version 1.00 - 12/21/2010

Summary of Contents for 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 1996 LAND CRUISER

Metra Electronics 99-3010S Installation Instructions Manual preview
99-3010S
Brand: Metra Electronics Pages: 14
GARO TWIN+ Assembly Instructions / End User Instruction preview
TWIN+
Brand: GARO Pages: 23
GARO LS4 Wallmounted Operational Instructions preview
LS4 Wallmounted
Brand: GARO Pages: 15
Vauxhall Cascada Quick Reference Manual preview
Cascada
Brand: Vauxhall Pages: 2
Jeep GRAND CHEROKEE 2023 Information Manual preview
GRAND CHEROKEE 2023
Brand: Jeep Pages: 108
UMBRA RIMORCHI 39030 Installation Instructions Manual preview
39030
Brand: UMBRA RIMORCHI Pages: 18
NavLinkz CAM-N-CV133-V Manual preview
CAM-N-CV133-V
Brand: NavLinkz Pages: 4
Ford 2008 Mustang Quick Reference Manual preview
2008 Mustang
Brand: Ford Pages: 2
Jeep GLADIATOR 2022 Owner'S Manual preview
GLADIATOR 2022
Brand: Jeep Pages: 380
T-Mobile SyncUP DRIVE Start Manual preview
SyncUP DRIVE
Brand: T-Mobile Pages: 2
BMW M3 SEDAN Owner'S Manual preview
M3 SEDAN
Brand: BMW Pages: 392
Curt Manufacturing 13434 Installation Instructions preview
13434
Brand: Curt Manufacturing Pages: 4
PEUGEOT BOXER 2018 Handbook preview
BOXER 2018
Brand: PEUGEOT Pages: 232
Volvo 30661683 Installation Instructions, Accessories preview
30661683
Brand: Volvo Pages: 18
Car-Interface CI-RL4-MM-NP Manual preview
CI-RL4-MM-NP
Brand: Car-Interface Pages: 23
Gacell SLH 27C User Manual preview
SLH 27C
Brand: Gacell Pages: 25
Guardsman G14776S Fitting Instruction preview
G14776S
Brand: Guardsman Pages: 2
Blue Ox BX2323 Installation Instructions Manual preview
BX2323
Brand: Blue Ox Pages: 9

Brands by name

Popular brands

Load more brands