manualshive.com logo in svg

Toyota 1996 LAND CRUISER, User Manual, Page: 305 / 1381

Share
Download
Toyota 1996 LAND CRUISER User Manual Download Page 305

BO4047

Point Marks

BO

−

66

−

BODY

SLIDING ROOF

1996 LAND CRUISER   (RM451U)

33. ADJUST DRIVE RAIL

HINT:
Adjust the drive rail to a closed and tilted down position.
Using a screwdriver, slide the link forward or backward to align
the 2 marks, as shown.

34. ADJUST AND INSTALL DRIVE GEAR ASSEMBLY

(a)

Remove the screw and cam plate cover.

(b)

Remove the large screw, washers and shims.

(c)

Turn the drive shaft by screwdriver to align the housing
and gear point mark, as shown.

(d)

Install the cam plate cover with the screw.

(e)

Install the drive gear assembly with 4 bolts.

(f)

Connect the connector.

35. INSTALL DRIVE GEAR CONTROL RELAY AND

BRACKET

(a)

Install the bracket with 2 bolts.

(b)

Install the drive gear control relay with the bolt, then con-
nect the connector.

Brought to you by BirfMark

Brought to you by BirfMark 
 Version 1.00 - 12/21/2010

Summary of Contents for 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments