![background image](http://html1.mh-extra.com/html/omron/sysmac-c500-nc113/sysmac-c500-nc113_operation-manual_742437100.webp)
6-3
Section
%
+)
Word
Function
Bit
m+4
m+8
15
External input protect (Word m+4 only)
ON: External inputs are disabled.
OFF: External inputs are enabled.
Even if the external input protect is turned ON, the CW and CCW limit inputs will remain enabled.
The following external inputs are protected.
•
Interrupt input
•
Origin proximity input
•
Immediate stop input
•
Origin input
•
Positioning completion input
Note The NC113 is not provided with the Y axis.
6-3
When the PC is in Program Mode
6-3-1 Command Configuration (Program Mode)
The following table shows the commands that are can be used when the Pro-
grammable Controller (i.e., the CPU Unit) is in Program Mode. Word “n” repre-
sents the first of the two I/O words allocated for the Special I/O Unit.
Bit
Word n (output)
Remarks
00
Reserved for system.
---
01
Reserved for system.
---
02
Reserved for system.
---
03
Operating mode
---
04
X-AXIS ORIGIN SEARCH
X-axis commands in Program Mode
05
X-AXIS ERROR RESET
g
06
X-AXIS CW JOG
07
X-axis high-speed jogging /
low-speed jogging designation
08
X-AXIS CCW JOG
09
Reserved for system
---
10
Y-AXIS ORIGIN SEARCH
Y-axis commands in Program Mode
11
Y-AXIS ERROR RESET
g
12
Y-AXIS CW JOG
13
Y-axis high-speed / low-speed
jogging designation
14
Y-AXIS CCW JOG
15
Reserved for system.
---
When bit 03 is OFF (i.e., Program Mode), bits 04 to 15 are enabled for the Posi-
tion Control Unit. The NC113 is provided with the X axis only. Bits 10 to 14 will be
ignored by the NC113.
Note When the CPU Unit is in either Run or Monitor Mode, bit 03 must be turned ON by
the program. When bit 03 is OFF, commands cannot be received by means of
WRIT (the Intelligent I/O Write instruction).
Ladder Program Example
Always ON
Operating mode
Bit 03
If bit 03 is turned ON by a forced set when the CPU Unit is in Program Mode, the
Position Control Unit will stop all operations in Program Mode.
Summary of Contents for SYSMAC C500-NC113
