![background image](http://html.mh-extra.com/html/mitsubishi-electric/melsec-l-series/melsec-l-series_user-manual_238757348.webp)
6 - 6
Chapter 6 Sequence Program Used for Positioning Control
6.2 List of devices used
In the sequence programs using LD77MS4 shown in this chapter and subsequent, the
application of the devices used are as follows.
The I/O numbers for Simple Motion module indicate those when the head I/O number
is set to "0H".
If it is set to other than "0H", change the I/O number according to setting of head I/O
number.
In addition, change the external inputs, external outputs, internal relays, data resisters,
and timers according to the system used.
(1) Inputs/outputs, external inputs/external outputs, and internal relays
of LD77MS4
Device name
Device
Application
Details when ON
Axis 1 Axis 2 Axis 3 Axis 4
Inputs/
outputs
of
LD77MS4
Input
X0
READY signal
LD77MS preparation completed
X1
Synchronization flag
LD77MS buffer memory accessible
X4
X5
X6
X7 M code ON signal
M code outputting
X8
X9
XA
XB Error detection signal
Error detected
XC
XD
XE
XF BUSY signal
BUSY (operating)
X10
X11
X12
X13 Start complete signal
Start completed
X14 X15 X16 X17
Positioning
complete
signal
Positioning
completed
Out-
put
Y0
PLC READY signal
PLC CPU preparation completed
Y1
All axis servo ON signal
All axis servo ON signal
Y4
Y5
Y6
Y7 Axis stop signal
Requesting stop
Y8
YA
YC
YE Forward run JOG start signal
Starting forward run JOG
Y9
YB
YD
YF Reverse run JOG start signal
Starting reverse run JOG
Y10 Y11 Y12 Y13
Positioning
start
signal
Requesting
start
Y14
Y15
Y16
Y17 Execution prohibition request
Execution prohibition
External input
(command)
X20
—
OPR request OFF command
Commanding OPR request OFF
X21
External command valid command
Commanding external command valid
setting
X22
External command invalid command
Commanding external command
invalid
X23
Machine OPR command
Commanding machine OPR
X24
Fast OPR command
Commanding fast OPR
X25
Positioning start command
Commanding positioning start
X26
Speed-position switching operation
command
Commanding speed-position switching
operation
X27
Speed-position switching enable
command
Commanding speed-position switching
enable
X28
Speed-position switching prohibit
command
Commanding speed-position switching
prohibit
X29
Movement amount change
command
Commanding movement amount
change
X2A
High-level positioning control start
command
Commanding high-level positioning
control start
X2B
Positioning start command
(dedicated instruction)
Commanding positioning start
Summary of Contents for MELSEC-L Series
