![background image](http://html.mh-extra.com/html/mitsubishi-electric/melsec-l-series/melsec-l-series_user-manual_238757538.webp)
9 - 78
Chapter 9 Major Positioning Control
Positioning data setting examples
[When "1-axis speed control (forward run: speed 1)" is set in the positioning data
No. 1 of axis 1]
Setting item
Setting example
Setting details
LD77MS2
LD77MS4
LD77MS16
Axis 1
Pos
itioning d
ata N
o. 1
Da.1 Operation pattern
Positioning complete
Setting other than "Positioning complete" is not possible in
speed control.
Da.2 Control method
Forward run speed 1 Set 1-axis speed control.
Da.3 Acceleration time No.
1
Designate the value set in "
Pr.25
Acceleration time 1
" as the
acceleration time at start.
Da.4 Deceleration time No.
0
Designate the value set in "
Pr.10
Deceleration time 0
" as the
deceleration time at deceleration.
Da.5
Axis to be interpolated
LD77MS2
LD77MS4
–
Setting not required (setting value is ignored).
Da.6
Positioning address/
movement amount
–
Da.7 Arc address
–
Da.8 Command speed
6000.00mm/min
Set the speed to be commanded.
Da.9
Dwell time/JUMP
destination
positioning data No.
–
Setting not required (setting value is ignored).
Da.10
M code/Condition
data No./Number of
LOOP to LEND
repetitions
10
Set this when other sub operation commands are issued in
combination with the No. 1 positioning data. ("
Pr.18
M code ON
signal output timing
" setting only possible in the WITH mode.)
Da.20
Axis to be interpolated
No.1
LD77MS16
–
Setting not required (setting value is ignored).
Da.21
Axis to be interpolated
No.2
LD77MS16
–
Da.22
Axis to be interpolated
No.3
LD77MS16
–
(Note): Refer to Section 5.3 "List of positioning data" for information on the setting details.
Summary of Contents for MELSEC-L Series
