manualshive.com logo in svg

Ericsson AVP 4000, Reference Manual, Page: 49 / 422

Share
Download
Ericsson AVP 4000 Reference Manual Download Page 49

 

Getting Started 

 

 

1/1553-FGC 101 1790 Uen Y

 

 

3-13 

 

 

 

Parameter 

Values 

Description 

Comments 

Duplex Mode 

Auto 

Auto negotiate the mode 

 

Full Duplex 

Simultaneously transmit and receive 

Half Duplex 

Transmit and receive in a time 

division manner 

Default Virtual MAC 

Address 

aa:bb:cc:dd:ee:ff 

The virtual MAC address of the Gex 

interface. 

Read only parameter 

IP Address 

aaa.bbb.ccc.ddd 

IP address of the data interace 

group 

 

Subnet Mask 

0.0.0.0 [default] 
aaa.bbb.ccc.ddd 

Subnet mask for the data interface 

group 

 

Default Gateway 

0.0.0.0 [default] 

No defined gateway 

 

aaa.bbb.ccc.ddd 

Gateway address for packets 

outside the defined subnet 

 

IGMP mode selection 
 

IGMP v3 

Uses version 3 of the IGMP protocol   

IGMP v2 

Uses version 2 of the IGMP protocol   

Physical Data Interface <n> 

Default MAC Address 

aa:bb:cc:dd:ee:ff 

The MAC address of the Gex 

interface. 

Read only parameter 

Link Status 

Link Up (1000) 

Link is up and the link speed is 

1000 Mbps. 

Read only parameter 

Link Up (100) 

Link is up and the link speed is 

100 Mbps. 

Link Down 

Link is down. 

Link Up Time 

days : hours : mins : secs 

The length of time that the link has 

been up. If the link goes down this 

value is reset to 0. 

Read only parameter 

TX Packets 

 

Number of IP packets transmitted 

Read only parameter 

RX Packets 

 

Number of IP packets received 

Read only parameter 

IP Address 

aaa.bbb.ccc.ddd 

IP address of the data interface 

 

Data Output 

The unit can generate one or more output Transport Streams from the components 

produced by the option cards fitted. The IP output Transport Stream packets are 

encapsulated in IP packets prior to being transmitted via the Ethernet Data ports. 

The base unit does not provide any other interface through which Transport Streams 

can be output. 

Data Input 

The unit has two Ethernet ports for data input, and responds to ARPs, pings and 

Reflex PCR exchange messages for statistical multiplexing. The input of data is only 

supported for transcoded operation. 

Summary of Contents for AVP 4000







































































































































































































































































































































































































































Reviews:

No comments