Ericsson AVP 4000 Reference Manual Download Page 246

Page: 246 / 422

Web GUI Control

5-62

1/1553-FGC 101 1790

Uen

Parameter

Values

Description

2016, Video Index, WSS-AFD/WSS, user set Aspect

Ratio. Bar Data is only SMPTE 2016. This setting is not

available (not visible) when Super Low Delay Buffer Mode

is selected.

TC Output Location

Off, SEI Message

Defines how timecode is put into the output video stream.

This setting is not available (not visible) when Super Low

Delay Buffer Mode is selected.

Closed Captions

Off, ATSC (default)

Controls if Closed Captions are included in the output

stream. This setting is not available (not visible) when

Super Low Delay Buffer Mode is selected.

Video Component

The following parameters are available on the

Component

tab of the

Properties

widget on the

Service Configuration

page when a video component is selected in

the

Outputs

widget. The same parameters can be accessed through the

Output/<output name>/Transport Stream ID: <n>/Service List/<service

name>/Component List/Slot <x> Video Stream on PID <y>

menu on the front

panel.

Table 5.38 Video Component Parameters

Parameter

Values

Description

PID

16 to 8190

Sets the packet identifier associated with the component.

Bit Rate Weighting

Fixed, Minimum, 2 to 20

Specifies the weight associated to the component in the

Bit Rate Tracking algorithm.

Master TS

Off, On

Sets the master Transport Stream for the component.

Source PID Monitoring None, Monitor, Monitor & Redundancy

Priority 1 ETR290 monitoring on this PID from an IP input

can be enabled, and can be set to cause a redundancy

switch to a spare device if in a system controlled by

Ericsson control software. Not supported in this release.

Multichannel Restrictions

The first channel must always be set to encode. If this is set to OFF, then it will not

be possible to encode any video stream. If there are to be mixed frame rates, the

highest frame rate of all channels must be present on channel 1.

•

It is not possible to mix 25 Hz and 29.97 Hz on the same card.

•

It is not possible to mix 50 Hz and 59.94 Hz on the same card.

GOP Structure

•

There is no restriction across the channels. Each channel may have a different

GOP structure.

Bit Rate

•

There is no restriction across the channels. Each channel may have a different

bit rate. If two or more channels are in use the bit rate for each channel may not

exceed 30 Mbps.

Summary of Contents for AVP 4000







































































































































































































































































































































































































































Search results

Summary of Contents for AVP 4000

Reviews:

Ericsson AVP 4000, Reference Manual, Page: 246 / 422

Search results

Summary of Contents for AVP 4000

Reviews: