manualshive.com logo in svg

Ericsson AVP 4000, Reference Manual, Page: 228 / 422

Share
Download
Ericsson AVP 4000 Reference Manual Download Page 228

 

 

Web GUI Control  

 

5-44 

 

1/1553-FGC 101 1790 

Uen

 Y

  

 

 

 

Parameter 

Values 

Description 

Delay 

1000 

Specifies the delay ??? (in ms). 

Operation Mode 

Line out mode, ??? 

Specifies if operation mode. 

drcHighCut 

0.0 

Specifies drcHighCut. 

drcLowBoost 

0.0 

Specifies drcLowBoost. 

Audio Encoding 

The following parameters are available on the 

Encode

 tab of the 

Properties

 widget on the 

Service Configuration

 page when an audio component is selected in the 

Outputs

 widget. 

The same parameters can be accessed through the 

Advanced/EI9001/Audio 

Module/Audio <n>/Encode

 menu on the front panel.

 

Table 5.15  Audio Encoding Standards 

Parameter 

Options 

Description 

Coding Standard

 

MPEG Layer 2 

MPEG Layer 2 Encode (more than two channel pairs 

require the AVP/SWO/M1L2 license). 

Dolby Digital 

Dolby Digital encode, requires AVP/SWO/DOLBYAC3 

license.  

Dolby Digital Plus 

Dolby Digital Plus encode, requires 

AVP/SWO/DOLBY/PLUS license.  

AAC-LC 

AAC-LC encoding, requires AVP/SWO/AAC license. 

HE-AAC 

HE-AAC or HE-AAC v2 encoding, requires 

AVP/SWO/AAC license. 

Pass-thru 

Pass-thru of the input. 

Audio Description Service 

MPEG-1 Layer II encode of a mono audio track that 

describes action in the video plus a control track. 

Table 5.16  MPEG-1 Layer 2 Parameters 

Parameter 

Values 

Description 

Bit Rate 

32, 48, 56, 64, 80, 96, 112, 128, 160, 192, 224, 

256, 320, 384 

Bit Rate of the audio stream. 

Coding Mode 

1/0 (Left - input), 1/0 (Right - input), 1/0 (L+R)/2, 

1+1 (L/Ch1, R/Ch2), 2/0, 2/0 (Joint), Phase 

Aligned Audio (6 Cannels), Phase Aligned Audio 

(8 Channels) 

Specifies what channel configuration to use for encoding. 

Embedded PCR 

On, Off 

Controls whether PCR is to be embedded in the audio 

PES. 

Au Information Cont 

Off, AU Info 

Controls the insertion of private data in the adaptation unit 

of the audio access units (AU). AU Info is defined in ETSI 

TR 101 154. Only AU_PTS is present for audio. 

Advanced 

Lip Sync Offset 

-500 to 500 ms 

Configures a delay to the audio to improve A/V 

synchronization. 

Gain 

-6 to 6dB 

Sets the gain in dB for the audio stream. 

Summary of Contents for AVP 4000







































































































































































































































































































































































































































Reviews:

No comments