Ericsson AVP 4000 Reference Manual Download Page 151

Page: 151 / 422

Front Panel Control

1/1553-FGC 101 1790 Uen Y

4-11

Active Interface

Read only parameter. In Active - Active redundancy mode both

interfaces are active.

Line Speed

Auto, 100 Mpbs, 1 Gbps. The transmission speed of the link.

Duplex Mode

Auto, Full Duplex, Half Duplex. Determines whether data are to be

transmitted and received in a time divided manner (Half Duplex) or

transmission and reception can happen at the same time over the

same link (Full Duplex). Auto is for automatic configuration.

Default Virtual MAC Address

Virtual MAC address assigned to the Data Interface Group.

IP Address

The IP address associated with the interface group.

Subnet Mask

The subnet mask associated with the interface group.

Gateway Address

The gateway address associated with the interface group.

IGMP mode Selection

IGMP v2, IGMP v3

Physical Data Interface <k>

The physical data interface labeled as Ge <k> of the current data

interface group.

Default MAC Address

The hardware address of the Ge <k> interface.

Link Status

Link Down, Link Up. The status of the current physical data

interface.

Link Up Time

The time in days, hours, minutes and seconds the link is

established. Read only parameter.

TX Packets

Packets transmitted since the link is up.

RX Packets

Packets received since the link is up.

IP Address

The IP address of the physical data interface.

Add New Transport Stream

Creates a new Transport Stream for the current output.

Add Existing Transport Stream

Creates a copy of an existing Transport Stream for the current

output.

Transport Stream <l>

The list of the Transport Streams to copy to the current output.

Transport Stream ID <id>

Selects the Transport Stream with ID <id> to modify its parameters.

Service List

The list of services in the current Transport Stream.

Add Service

Adds a new service to the current Transport Stream.

Service <name>

Selects the service with <name> already added to the current

Transport Stream.

Component List

List of components in the current service.

Add Component

Adds a new component to the current service.

Selects the component with <component name> and <pid> already

added to the current service.

Elementary Stream

The elementary stream associated with the component produced by

one of the CE VCM modules in the unit.

PID

The Packet Identifier that identifies the TS packets carrying the

current component.

Summary of Contents for AVP 4000







































































































































































































































































































































































































































Search results

Summary of Contents for AVP 4000

Reviews:

Ericsson AVP 4000, Reference Manual, Page: 151 / 422

Search results

Summary of Contents for AVP 4000

Reviews: