Ericsson AVP 4000 Reference Manual Download Page 408

Page: 408 / 422

Alarm Lists

D-18

1/1553-FGC 101 1790 Uen X

Alarm

Description

Port Number

Alarm ID

Source

Severity

Audio 10 ADS control track

Control track for audio description

not present.

03122128

Audio 10

minor

Audio 10 ADS silence

Silent period detected. Valid only for

Audio Description Service encoding.

03122129

Audio 10

minor

Audio 10 Clipping

Audio output is clipping. Audio gain

value or input amplitude should be

reduced.

0312212A

Audio 10

minor

Audio 10 VPS/ARIB Coding

Mode Mismatch

The coding mode signalled by

VPS/ARIB is not supported by the

current Audio Codec

0312212B

Audio 10

minor

Audio 11 Input lock

No valid audio detected on selected

input. Please check source

connection.

03122140

Audio 11

major

Audio 11 TS input error

Incoming transport stream error.

Please check source TS.

03122141

Audio 11

major

Audio 11 Compressed audio not

detected

Compressed audio not detected on

input. Please check source

connection and source format.

03122142

Audio 11

minor

Audio 11 Input frame CRC

failure

CRC error in compressed input

frame. Output is muted.

03122143

Audio 11

minor

Audio 11 Unsupported sample

rate

Unsupported sample rate at decoder

output.

03122144

Audio 11

minor

Audio 11 Dolby E program not

present

Program not present in Dolby E

stream.

03122145

Audio 11

minor

Audio 11 Dolby E alignment

Dolby E frames not properly aligned

to video frames. May glitch on frame

drop/repeat and video may not be

aligned to audio.

03122146

Audio 11

minor

Audio 11 Dolby E metadata

frame rate mismatch

Frame rate indicated in Dolby E

metadata does not match current

video frame rate.

03122147

Audio 11

minor

Audio 11 ADS control track

Control track for audio description

not present.

03122148

Audio 11

minor

Audio 11 ADS silence

Silent period detected. Valid only for

Audio Description Service encoding.

03122149

Audio 11

minor

Audio 11 Clipping

Audio output is clipping. Audio gain

value or input amplitude should be

reduced.

0312214A

Audio 11

minor

Audio 11 VPS/ARIB Coding

Mode Mismatch

The coding mode signalled by

VPS/ARIB is not supported by the

current Audio Codec

0312214B

Audio 11

minor

Audio 12 Input lock

No valid audio detected on selected

input. Please check source

connection.

03122160

Audio 12

major

Audio 12 TS input error

Incoming transport stream error.

Please check source TS.

03122161

Audio 12

major

Audio 12 Compressed audio not

detected

Compressed audio not detected on

input. Please check source

connection and source format.

03122162

Audio 12

minor

Summary of Contents for AVP 4000







































































































































































































































































































































































































































Search results

Summary of Contents for AVP 4000

Reviews:

Ericsson AVP 4000, Reference Manual, Page: 408 / 422

Search results

Summary of Contents for AVP 4000

Reviews: