manualshive.com logo in svg

Ericsson AVP 4000, Reference Manual, Page: 262 / 422

Share
Download
Ericsson AVP 4000 Reference Manual Download Page 262

 

 

Web GUI Control  

 

5-78 

 

1/1553-FGC 101 1790 

Uen

 Y

  

 

 

 

Parameter 

Values 

Description 

Alignment 

Block Aligned, Non Block Aligned 

The aligned method used for ProMPEG FEC.  

MGP Settings

1 

1

Only available in MGP Module Level mode and if the unit is not controlled by Ericsson control software

 

MSM Multicast 

Address 

IP v4 multicast address 

Destination for MGP Status Messages. Transport streams 

sharing this value belong to the same media bundle and are 

switched on or off together. 

MGP State 

R0 Not In Service, S0 Not in Service, S1 

Activated Spare, R1 On air 

State of the bundle the transport stream belongs to. Read only. 

IP Configuration/Destination 1 

Destination IP 

Address 

aaa.bbb.ccc.ddd 

The destination IP address to use in the IP packet header of 

the IP packets that carry the Transport Stream 

Destination UDP Port 

0 to 65535 

The destination UDP port to use in the IP packet header of the 

IP packets that carry the Transport Stream 

Source IP Address 

aaa.bbb.ccc.ddd 

The source IP address to use in the IP packet header of the IP 

packets that carry the Transport Stream 

Source MAC Address 

 

Read only parameter, not yet supported. 

Source UDP Port 

0 to 65535 

The source UDP port to use in the IP packet header of the IP 

packets that carry the Transport Stream 

Vlan Header 

Disabled, Enabled. 

 

Vlan ID Tag 

 

 

Vlan Tag 

 

The VLAN tag to use for the current IP stream.  

Vlan Priority 

0 to 7 

The priority to be used by the switches to prioritize different 

services. 

Time To Live 

0 to 240 

TTL value for inclusion in the IP header 

Type Of Service 

0 to 255 

ToS value for inclusion in the IP header 

Actual source IP 

address, calculated by 

a rule 

aaa.bbb.ccc.ddd 

The source IP address. Read only parameter 

Actual source MAC 

address, calculated by 

a rule 

 

The source MAC address. Read only parameter. 

MGP Settings

1

 

Spare IP Address 

IP v4 address 

Address used as source for MGP Status Message IP packets, 

generally the IP address assigned to an output interface of a 

peer (backup) unit. 

Service Settings 

The service parameters are available in the 

Properties

 widget on the 

Service 

Configuration

 page if a service is selected in the 

Outputs

 widget. The same 

settings are also available through the front panel under 

Output/<IP interface 

name>/<Transport Stream name>/Service List/<service name>

. 

Summary of Contents for AVP 4000







































































































































































































































































































































































































































Reviews:

No comments