manualshive.com logo in svg

Ericsson AVP 4000, Reference Manual, Page: 224 / 422

Share
Download
Ericsson AVP 4000 Reference Manual Download Page 224

 

 

Web GUI Control  

 

5-40 

 

1/1553-FGC 101 1790 

Uen

 Y

  

 

 

 

Parameter 

Values 

Description 

Closed GOPs 

Off, On 

Enables or disables the usage of Group of Pictures in 

which the predicted frames can have their reference from 

outside the group. 

Delay 

 

Displays the actual video encoding delay. Read only 

parameter. 

Inloop Filter 

High, Normal, Low, Very Low, Auto 

Sets the characteristics of the filter placed in the feedback 

loop of the encoder. Applying the filter to the picture can 

increase picture sharpness. 

SEI Encapsulation 

Mode 

2

 

Combined, Mediaroom  

Sets the SEI messages in combined mode where all the 

SEI messages are combines into one NAL unit or into 

Mediaroom mode compliance where each SEI message 

has its own NAL start.  

1

 Only applicable when the video profile is set to MPEG-2. 

2

 Only applicable when the video profile is set to H.264. 

Specific Notes on Second Video 

The Main Video and the Second Video (this also applies to the PiP Component) 

originate from the same input; therefore they naturally share the timing information: 

•

  They have the same clock reference (PCR) value in the stream, whether they 

use embedded PCR or a separate PCR component. 

•

  Their timing (PTS) are aligned, and it is therefore possible to share audio 

components from the same card. 

Restrictions on the Second Video Compared to the Main Video 

•

  The Second Video supports SD encoding only and does not support HD 

encoding resolutions. The codec for the secondary video component is 

restricted to that detailed in the table below. 

Table 5.10  Restrictions on Secondary Video Component Coding Standard 

Primary Video Component Coding Standard 

Secondary Video Component Coding Standard 

SD MPEG-2 

Off, SD MPEG-2, SD H.264 

SD H.264 

Off, SD H.264 

HD MPEG-2 

Off, SD MPEG-2 

HD H.264 

Off, SD H.264 

•

  The Second Video component (this also applies to the PiP component) cannot 

be added to the same service as the Main Video component. It can be only be 

added to a separate service. 

•

  The Second Video can be turned Off by setting the Video profile to Off. 

•

  The Second Video only supports CBR, and therefore does not support VBR and 

Reflex. 

•

  The Premium License does not apply to the Second Video. 

Summary of Contents for AVP 4000







































































































































































































































































































































































































































Reviews:

No comments