manualshive.com logo in svg

Ericsson AVP 4000, Reference Manual, Page: 244 / 422

Share
Download
Ericsson AVP 4000 Reference Manual Download Page 244

 

 

Web GUI Control  

 

5-60 

 

1/1553-FGC 101 1790 

Uen

 Y

  

 

 

 

Parameter 

Values 

Description 

Profile for 3G input 

Profile Off, 
HDp50/59.94 HEVC Main Profile Level 4.1 High Tier 4:2:0 8 bit, 
HDp50/59.94 HEVC Main Profile Level 4.1 High Tier 4:2:0 10 bit, 
HDp50/59.94 HEVC Main Profile Level 4.1 High Tier 4:2:2 8 bit, 
HDp50/59.94 HEVC Main Profile Level 4.1 High Tier 4:2:2 10 bit 

The profile to set when a 3G input is 

detected on the SDI input. Visible only if 

Input Detection

 is set to Auto Detect 

and Configure. If this option is visible, 

the 

Video Profile

 cannot be set 

manually. 

Profile for UHD input 

Profile Off, 
UHD HEVC Main 10 Profile Level 5.1 High Tier 4:2:0 10 bit, 
UHD HEVC Main 10 Profile Level 5.1 High Tier 4:2:2 10 bit 

The profile to set when an UHD input is 

detected on the SDI inputs. Visible only 

if 

Input Detection

 is set to Auto Detect 

and Configure. If this option is visible, 

the 

Video Profile

 cannot be set 

manually. 

Resolution 

1280 x 720, 1920 x 1080, 3840 x 2160 

Defines the horizontal and vertical 

resolution of the encoded video. The 

available options depend on the values 

set for 

Video Input Format

 and 

Video 

Profile

. 

Signalling Options 

SDR (BT.709), UHD SDR (BT.2020), HDR HLG10 (HDR in VUI), 

HDR HLG10 (SDR in VUI), HDR PQ10 

The HDR signalling option to be used. 

Video Bit Rate 

The valid bit rate range depends on the selected video profile. 

Defines the bit rate to be used by the 

compressed video component. If 

Bit 

Rate Tracking Mode

 is set to 

Maximize 

Video

 for the Transport Stream that 

contains the video component, and the 

Bit Rate Weighting

 of the component is 

set to other than 

Fixed

 or 

Minimal

, this 

field is read only. 

Buffer Mode 

CBR 

Constant Bit Rate operation. 

Low Delay 

Reduced encode delay achieved by 

removing pre-processing functions. Bit 

Rate, GOP structure and GOP length 

impact the delay. The IP GOP structure 

will give low delay, but with reduced 

quality.  

Mega Low Delay 

Encode delay reduced further by 

removing frame-sync in pre-processing. 

Bit Rate, GOP structure and GOP length 

impact the delay. The IP GOP structure 

will provide lower latency than Low 

Delay.  

Super Low Delay 

Only available for HEVC and a single 

channel: 
The lowest delay is achieved by 

removing GOP structure concepts and 

concentrating on striping of P Frames or 

complete I Frames. This selection will 

provide the best latency delay 

performance. No ANC stream 

processing is available in this mode.  

Aspect Ratio 

16:9, 4:3 

Does not affect the video encoding but 

rather indicates what the desired aspect 

ratio for the decoded picture (not the 

pixel). If no other mechanism such as 

WSS in the VBI is used, the video output 

image will use this aspect ratio. 

Summary of Contents for AVP 4000







































































































































































































































































































































































































































Reviews:

No comments