manualshive.com logo in svg

Ericsson AVP 4000, Reference Manual, Page: 163 / 422

Share
Download
Ericsson AVP 4000 Reference Manual Download Page 163

 

Front Panel Control 

 

 

1/1553-FGC 101 1790 Uen Y

 

 

4-23 

 

 

 

 

 

MGP Mode 

Off, Module Level, Unit Level. Determines if MGP is enabled or not, or if it is enabled, 

then the unit is controlled as a whole or on a module level basis. 

 

 

Transmission Interval 

Period for steady-state transmission of MSM packets in units of ms. 

 

 

R0 Playout Period 

Duration of the MSM burst emitted on entering MGP state R0 in units of ms. 

 

 

S1 Playout Period 

Duration of the MSM burst emitted on entering MGP state S1 in units of ms. 

 

 

Control Contact Timeout 

Period of time in ms the system waits before assuming loss of contact with the control 

system after the control link goes down. 

 

 

MSM Destination Port 

UDP port for sending MGP packets. 

 

 

MGP Settings

1

 

1

Only available when MGP is enabled 

 

 

 

MSM Multicast Address 

The destination IP Address of the MSM packets. 

 

 

 

MGP State 

The current state of the MGP implementation. 

 

 

MGP Spares

2

 

2

Only available when MGP is enabled. 

 

 

 

Spare Device Configuration 

Selects a spare device to set up its parameters. 

 

 

 

 

Spare IP Address 

The IP address of another unit that is acting as a spare for this unit/service. 

 

Vlan Tags 

 

 

 

Output <n>: Data Port <m> - Data 

Port <k> 

Selects output <n> for adjusting its VLAN settings. 

 

 

 

Add Vlan tag 

Adds a new VLAN tag to the current output. 

 

 

 

Vlan ID: <id> 

The ID associated with the VLAN tag. Allows the user to change the ID. 

 

 

 

 

Vlan ID (Create) 

Modifies the VLAN ID for the current tag. 

 

 

 

 

Vlan IP 

Assigns an IP address to the VLAN. 

 

 

 

 

Vlan Netmask 

Specifies the network mask for the current VLAN. 

 

 

 

 

Vlan Gateway 

Specifies the gateway address for the current VLAN. 

 

 

 

 

Vlan Priority 

Specifies the gateway priority for the current VLAN. 1-7. 

 

SNMP 

 

 

 

System Contact 

Contact to the team providing support for this unit. 

 

 

System Name 

The name to identify the current unit. 

 

 

System Location 

The location where the current unit is installed. 

 

 

Will this unit be SNMP Polled 

True, False. Determines whether the unit is polled for SNMP information or not. 

 

 

Time Elapsed before Control 

assumed Lost 

The amount of time between sysUpTime requests before the connection with the 

control system is assumed to be down. 

 

 

Currently in Contact with Control 

System 

Determines if a connection has been established with the trap server. True/False. 

 

 

SNMP Agent Ready 

Determines if the SNMP agent is ready. True/False. 

 

 

SNMP Trap Server 

Configures the Trap Server destinations. 

 

Accept Configuration 

Accepts the changes in hardware configuration if there are any. 

Summary of Contents for AVP 4000







































































































































































































































































































































































































































Reviews:

No comments