Ericsson AVP 4000 Reference Manual Download Page 406

Page: 406 / 422

Alarm Lists

D-16

1/1553-FGC 101 1790 Uen X

Alarm

Description

Port Number

Alarm ID

Source

Severity

Audio 7 Dolby E alignment

Dolby E frames not properly aligned

to video frames. May glitch on frame

drop/repeat and video may not be

aligned to audio.

031220C6

Audio 7

minor

Audio 7 Dolby E metadata frame

rate mismatch

Frame rate indicated in Dolby E

metadata does not match current

video frame rate.

031220C7

Audio 7

minor

Audio 7 ADS control track

Control track for audio description

not present.

031220C8

Audio 7

minor

Audio 7 ADS silence

Silent period detected. Valid only for

Audio Description Service encoding.

031220C9

Audio 7

minor

Audio 7 Clipping

Audio output is clipping. Audio gain

value or input amplitude should be

reduced.

031220CA

Audio 7

minor

Audio 7 VPS/ARIB Coding Mode

Mismatch

The coding mode signalled by

VPS/ARIB is not supported by the

current Audio Codec

031220CB

Audio 7

minor

Audio 8 Input lock

No valid audio detected on selected

input. Please check source

connection.

031220E0

Audio 8

major

Audio 8 TS input error

Incoming transport stream error.

Please check source TS.

031220E1

Audio 8

major

Audio 8 Compressed audio not

detected

Compressed audio not detected on

input. Please check source

connection and source format.

031220E2

Audio 8

minor

Audio 8 Input frame CRC failure

CRC error in compressed input

frame. Output is muted.

031220E3

Audio 8

minor

Audio 8 Unsupported sample

rate

Unsupported sample rate at decoder

output.

031220E4

Audio 8

minor

Audio 8 Dolby E program not

present

Program not present in Dolby E

stream.

031220E5

Audio 8

minor

Audio 8 Dolby E alignment

Dolby E frames not properly aligned

to video frames. May glitch on frame

drop/repeat and video may not be

aligned to audio.

031220E6

Audio 8

minor

Audio 8 Dolby E metadata frame

rate mismatch

Frame rate indicated in Dolby E

metadata does not match current

video frame rate.

031220E7

Audio 8

minor

Audio 8 ADS control track

Control track for audio description

not present.

031220E8

Audio 8

minor

Audio 8 ADS silence

Silent period detected. Valid only for

Audio Description Service encoding.

031220E9

Audio 8

minor

Audio 8 Clipping

Audio output is clipping. Audio gain

value or input amplitude should be

reduced.

031220EA

Audio 8

minor

Audio 8 VPS/ARIB Coding Mode

Mismatch

The coding mode signalled by

VPS/ARIB is not supported by the

current Audio Codec

031220EB

Audio 8

minor

Audio 9 Input lock

No valid audio detected on selected

input. Please check source

connection.

03122100

Audio 9

major

Summary of Contents for AVP 4000







































































































































































































































































































































































































































Search results

Summary of Contents for AVP 4000

Reviews:

Ericsson AVP 4000, Reference Manual, Page: 406 / 422

Search results

Summary of Contents for AVP 4000

Reviews: