Ericsson AVP 4000 Reference Manual Download Page 409

Page: 409 / 422

Alarm Lists

1/1553-FGC 101 1790 Uen X

D-19

Alarm

Description

Port Number

Alarm ID

Source

Severity

Audio 12 Input frame CRC

failure

CRC error in compressed input

frame. Output is muted.

03122163

Audio 12

minor

Audio 12 Unsupported sample

rate

Unsupported sample rate at decoder

output.

03122164

Audio 12

minor

Audio 12 Dolby E program not

present

Program not present in Dolby E

stream.

03122165

Audio 12

minor

Audio 12 Dolby E alignment

Dolby E frames not properly aligned

to video frames. May glitch on frame

drop/repeat and video may not be

aligned to audio.

03122166

Audio 12

minor

Audio 12 Dolby E metadata

frame rate mismatch

Frame rate indicated in Dolby E

metadata does not match current

video frame rate.

03122167

Audio 12

minor

Audio 12 ADS control track

Control track for audio description

not present.

03122168

Audio 12

minor

Audio 12 ADS silence

Silent period detected. Valid only for

Audio Description Service encoding.

03122169

Audio 12

minor

Audio 12 Clipping

Audio output is clipping. Audio gain

value or input amplitude should be

reduced.

0312216A

Audio 12

minor

Audio 12 VPS/ARIB Coding

Mode Mismatch

The coding mode signalled by

VPS/ARIB is not supported by the

current Audio Codec

0312216B

Audio 12

minor

Audio 13 Input lock

No valid audio detected on selected

input. Please check source

connection.

03122180

Audio 13

major

Audio 13 TS input error

Incoming transport stream error.

Please check source TS.

03122181

Audio 13

major

Audio 13 Compressed audio not

detected

Compressed audio not detected on

input. Please check source

connection and source format.

03122182

Audio 13

minor

Audio 13 Input frame CRC

failure

CRC error in compressed input

frame. Output is muted.

03122183

Audio 13

minor

Audio 13 Unsupported sample

rate

Unsupported sample rate at decoder

output.

03122184

Audio 13

minor

Audio 13 Dolby E program not

present

Program not present in Dolby E

stream.

03122185

Audio 13

minor

Audio 13 Dolby E alignment

Dolby E frames not properly aligned

to video frames. May glitch on frame

drop/repeat and video may not be

aligned to audio.

03122186

Audio 13

minor

Audio 13 Dolby E metadata

frame rate mismatch

Frame rate indicated in Dolby E

metadata does not match current

video frame rate.

03122187

Audio 13

minor

Audio 13 ADS control track

Control track for audio description

not present.

03122188

Audio 13

minor

Audio 13 ADS silence

Silent period detected. Valid only for

Audio Description Service encoding.

03122189

Audio 13

minor

Summary of Contents for AVP 4000







































































































































































































































































































































































































































Search results

Summary of Contents for AVP 4000

Reviews:

Ericsson AVP 4000, Reference Manual, Page: 409 / 422

Search results

Summary of Contents for AVP 4000

Reviews: