manualshive.com logo in svg

Ericsson AVP 4000, Reference Manual, Page: 412 / 422

Share
Download
Ericsson AVP 4000 Reference Manual Download Page 412

 

 

Alarm Lists  

 

D-22 

 

1/1553-FGC 101 1790 Uen X

  

 

 

 

D.3 

EI9001T Additional Alarms 

Table D.3  EI9001T Additional Alarms 

Alarm

 

Description

 

Port Number

 

Alarm ID

 

Source

 

Severity

 

Decoder Input Lock 

Transport stream lock failure at 

transcoder input 

0 

03100200 

RX8 

Decoder 

Module 

major 

Decoder Service Lock 

Selected service(program) id not 

present in SI tables 

0 

03100201 

RX8 

Decoder 

Module 

critical 

Decoder Video Lock 

Decoding error for selected video 

component 

0 

03100202 

RX8 

Decoder 

Module 

critical 

Decoder Audio Decode 1 Lock 

Decoding error for selected audio 

component 

0 

03100203 

RX8 

Decoder 

Module 

critical 

Decoder Audio Decode 2 Lock 

Decoding error for selected audio 

component 

0 

03100204 

RX8 

Decoder 

Module 

critical 

Decoder Closed Caption Not 

Present 

Closed Captions enabled but not 

present/inserted 

0 

03100207 

RX8 

Decoder 

Module 

cleared 

Decoder AFD Not Present 

AFD processing enabled but not 

present/inserted 

0 

03100208 

RX8 

Decoder 

Module 

cleared 

Decoder Broadcaster ID Not 

Present 

Broadcaster identifier enabled but 

not present/inserted 

0 

03100209 

RX8 

Decoder 

Module 

cleared 

Decoder VITC Not Present 

VITC enabled but not 

present/inserted 

0 

0310020A 

RX8 

Decoder 

Module 

cleared 

Card booted in Failsafe Mode 

Corrupted Main image, Please 

reload valid Main image 

0 

0310020B 

RX8 

Decoder 

Module 

minor 

Over Temperature Warning 

Failure to take action may cause 

permanent damage to the unit.  

Please check the fans are working 

correctly, and that the ambient 

temperature is not excessive. 

0 

0310020C 

RX8 

Decoder 

Module 

minor 

Over Temperature 

Failure to take action may cause 

permanent damage to the unit.  

Please switch off and refer to 

Customer Support. 

0 

0310020D 

RX8 

Decoder 

Module 

critical 

Decoder Card Failed to Boot 

The card has not signalled that it is 

ready to receive configurations. 

0 

0310020E 

RX8 

Decoder 

Module 

critical 

Decoder card not present 

The RX8 decoder could not be 

detected. 

0 

0310020F 

RX8 

Decoder 

Module 

critical 

RX8 Configuration Manager has 

terminated 

The RX8 Configuration Manager has 

unexpectedly terminated due to an 

unhandled exception. 

0 

03100210 

RX8 

Decoder 

Module 

critical 

Summary of Contents for AVP 4000







































































































































































































































































































































































































































Reviews:

No comments