Ericsson AVP 4000 Reference Manual Download Page 398

Page: 398 / 422

Alarm Lists

D-8

1/1553-FGC 101 1790 Uen X

Alarm

Description

Port Number

Alarm ID

Source

Severity

POIS URL not configured

An Acquisition Point Identity is

already configured, but the POIS url

is empty. Signal Processing Events

can't be sent to POIS. Add a valid

POIS URL in the AVP 4000 UI.

0000045D

Base Unit

minor

Invalid POIS URL configured

The configured POIS url is not a

valid http url . Signal Processing

Events can't be sent to POIS.Correct

the POIS URL in the AVP 4000 UI.

0000045E

Base Unit

minor

POIS connection failure

The unit could not contact the POIS

Server. Check the POIS URL using

a tool like cURL.

0000045F

Base Unit

major

Invalid response from POIS

The POIS response xml does not

contain any valid response signal.

Analyse the POIS response XML.

00000460

Base Unit

major

PCR Exchange message

timeout

PCR exchange message has not

arrived.

00000690

Reflex

controller

warning

Status message timeout

Status message has not arrived.

00000691

Reflex

controller

warning

Reflex StatMux algorithm failed

Reflex statistical multiplexing

algorithm returned with an error.

00000692

Reflex

controller

warning

MGP Failure

Failed to go online, previous online

device preventing transmission

00000491

Base Unit

major

MGP Collision

Potential duplicate transmission

detected

00000492

Base Unit

major

MGP Spurious

Spurious MSM packet detected

00000493

Base Unit

minor

CSM Contact lost

No CSMs received from Control

System

00000680

Base Unit

minor

Datagram loss is greater than 0

The datagram loss rate for the

Transport Stream is greater than 0.

000006B0 to

0000073F

Base Unit

major

Sequence number errors in

Transport Stream

There are sequence number errors

in the Transport Stream.

000007B0 to

0000083F

Base Unit

major

No data available for Input

Transport Stream

Both Primary and Backup Input

Transport Streams have failed.

00000500 to

0000057F

Base Unit

critical

Input Transport Stream running

on Backup

Primary Input Transport Stream has

failed.

00000580 to

000005FF

Base Unit

warning

Input Transport Stream missing

Input Transport Stream has failed.

00000600 to

0000067F

Base Unit

major

Excessive CC errors on PID

The PID monitor has detected

continuity count errors, which

exceed the windowed threshold.

0000BB0 to

0000C2F

Base unit

major

PID on data input network is

missing

The PID monitor has detected a PID

missing for at least the period set by

the user.

0000B30 to

0000BAF

Base unit

major

Summary of Contents for AVP 4000







































































































































































































































































































































































































































Search results

Summary of Contents for AVP 4000

Reviews:

Ericsson AVP 4000, Reference Manual, Page: 398 / 422

Search results

Summary of Contents for AVP 4000

Reviews: