Ericsson AVP 4000 Reference Manual Download Page 404

Page: 404 / 422

Alarm Lists

D-14

1/1553-FGC 101 1790 Uen X

Alarm

Description

Port Number

Alarm ID

Source

Severity

Audio 4 Unsupported sample

rate

Unsupported sample rate at decoder

output.

03122064

Audio 4

minor

Audio 4 Dolby E program not

present

Program not present in Dolby E

stream.

03122065

Audio 4

minor

Audio 4 Dolby E alignment

Dolby E frames not properly aligned

to video frames. May glitch on frame

drop/repeat and video may not be

aligned to audio.

03122066

Audio 4

minor

Audio 4 Dolby E metadata frame

rate mismatch

Frame rate indicated in Dolby E

metadata does not match current

video frame rate.

03122067

Audio 4

minor

Audio 4 ADS control track

Control track for audio description

not present.

03122068

Audio 4

minor

Audio 4 ADS silence

Silent period detected. Valid only for

Audio Description Service encoding.

03122069

Audio 4

minor

Audio 4 Clipping

Audio output is clipping. Audio gain

value or input amplitude should be

reduced.

0312206A

Audio 4

minor

Audio 4 VPS/ARIB Coding Mode

Mismatch

The coding mode signalled by

VPS/ARIB is not supported by the

current Audio Codec

0312206B

Audio 4

minor

Audio 5 Input lock

No valid audio detected on selected

input. Please check source

connection.

03122080

Audio 5

major

Audio 5 TS input error

Incoming transport stream error.

Please check source TS.

03122081

Audio 5

major

Audio 5 Compressed audio not

detected

Compressed audio not detected on

input. Please check source

connection and source format.

03122082

Audio 5

minor

Audio 5 Input frame CRC failure

CRC error in compressed input

frame. Output is muted.

03122083

Audio 5

minor

Audio 5 Unsupported sample

rate

Unsupported sample rate at decoder

output.

03122084

Audio 5

minor

Audio 5 Dolby E program not

present

Program not present in Dolby E

stream.

03122085

Audio 5

minor

Audio 5 Dolby E alignment

Dolby E frames not properly aligned

to video frames. May glitch on frame

drop/repeat and video may not be

aligned to audio.

03122086

Audio 5

minor

Audio 5 Dolby E metadata frame

rate mismatch

Frame rate indicated in Dolby E

metadata does not match current

video frame rate.

03122087

Audio 5

minor

Audio 5 ADS control track

Control track for audio description

not present.

03122088

Audio 5

minor

Audio 5 ADS silence

Silent period detected. Valid only for

Audio Description Service encoding.

03122089

Audio 5

minor

Audio 5 Clipping

Audio output is clipping. Audio gain

value or input amplitude should be

reduced.

0312208A

Audio 5

minor

Summary of Contents for AVP 4000







































































































































































































































































































































































































































Search results

Summary of Contents for AVP 4000

Reviews:

Ericsson AVP 4000, Reference Manual, Page: 404 / 422

Search results

Summary of Contents for AVP 4000

Reviews: