Ericsson AVP 4000 Reference Manual Download Page 331

Page: 331 / 422

Preventive Maintenance and Fault-finding

1/1553-FGC 101 1790 Uen Y

8-11

8.5.3

Power Supply Problems/Unit Not Working

If the unit Status LED is unlit, fault-find the problem as detailed in

Table 8.3

Table 8.3 Status LED Unlit Fault-finding

Step

Action

If Result of Action is Yes…

If Result of Action is No…

Is the LED/LCD display inactive

but the unit still working?

If the unit is clearly working

normally then the LED/LCD

Display itself is probably at

fault. Call a Service Engineer.

Proceed to next step.

Check Power Source

. Connect

a known-working piece of

equipment to the power source

outlet. Does it work?

The problem lies within the

unit or power cable. Proceed

to next step.

The problem lies with the power

source. Check building circuit

breakers, fuse boxes, etc. If

problem persists, contact the

electricity supplier.

Check Power Cable and Fuse

Unplug the power connector

from the unit and try it in another

piece of equipment. Does it

work?

The problem lies within the

unit. Proceed to next step.

The problem lies with either the

cable itself, or with the fuse in

the plug. Replace the fuse or try

to substitute another cable.

Check PSU Module(s) and

Fuse(s)

. Ensure the power

connector is unplugged.

Remove the fuse from the rear

panel connector and inspect it.

Has the fuse blown?

Replace the fuse with one of

the correct type and rating

(see

Annex B Technical

Specification)

. If the PSU still

does not work, unplug the

power cable and call a Service

Engineer.

Possible problem with the PSU

module. Call a Service Engineer.

8.5.3.1

Fuse Replacement

Please refer to the

Installation, Safety and Compliance Information for Ericsson

Compression Products Reference Guide

supplied with your product for full details of

how to replace the fuse in your product.

8.5.3.2

Lithium Battery

The lithium battery fitted within this product is not user replaceable and as such

should only be replaced by qualified service personnel.

8.5.4

Fan(s) Not Working/Overheating

The fan speed can be reduced (set to lowest noise) at low temperatures to allow the

unit to quickly attain operational temperature. In the event of overheating problems,

refer to

Table 8.4

Note:

Failure to ensure a free air-flow around the unit may cause overheating.

This condition is detected by a temperature sensor; it may be used to trigger

an automatic alarm.

Summary of Contents for AVP 4000







































































































































































































































































































































































































































Search results

Summary of Contents for AVP 4000

Reviews:

Ericsson AVP 4000, Reference Manual, Page: 331 / 422

Search results

Summary of Contents for AVP 4000

Reviews: