manualshive.com logo in svg

Ericsson AVP 4000, Reference Manual, Page: 176 / 422

Share
Download
Ericsson AVP 4000 Reference Manual Download Page 176

 

 

Front Panel Control  

 

4-36 

 

1/1553-FGC 101 1790 Uen Y

  

 

 

 

 

 

 

AU Information Ctrl 

Off, AU Info. Controls the insertion of private data in the adaptation unit of the 

audio access units (AU). AU Info is defined in ETSI TR 101 154. Only AU_PTS 

is present for audio. 

 

 

 

Passthrough 

 

 

 

 

 

Channel Mode 

 

 

 

 

 

Bit Depth 

 

 

 

 

 

Channel Identification 

 

 

 

 

Encapsulation 

MPEG 2 ADTS, MPEG4 LATM/LOAS. Specifies the encapsulation used for 

transmitting AAC content. It can be either MPEG-2 Audio Data Transport 

Stream or MPEG-4 Low Overhead Audio Stream based on MPEG-4 Low 

Overhead Audio Transport Multiplex. 

 

 

 

TNS (Temporal Noise Shaping) 

Off, On. Turns noise shaping on or off. 

 

 

 

PNS (Perceptual Noise Substitution) 

 

 

 

 

SBR Signalling 

Explicit, Implicit. Specifies how Spectral Band Replication is signaled. 

 

 

 

Automatic Loudness Control 

 

 

 

 

 

Operating Mode 

Off, Measure, M ALC, M ALC + LTLC.  

 

 

 

 

Target Level 

-40 to 0 (LKFS (LU). The desired Loudness level for the channel. 

 

 

 

 

Time Period 

5 to 120 minutes. This controls the responsiveness of the long term audio 

loudness level correction. 
A smaller number will result in the audio being adjusted more dynamically. A 

larger value will give a slower less noticeable adjustment. 

 

 

 

 

Peak Limit 

-20 to 0 dBFS. This controls a hard clipping limiter for the audio level.  This 

adjustment is based on the absolute peak level measured in dBFS.   
The peak limiter only operates in ‘M ALC’ and ‘M ALC + 

LTLC’ modes.   
If this value is set to 0 no limiting is performed 

 

 

 

 

Maximum Boost 

0 to 10 dB. This control determines the maximum amount of gain that the LTLC 

algorithm can apply. This is to prevent over adjustment which can lead to 

unwanted audio artifacts. This only applies when the operating mode is 

“M ALC + LTLC”. 

 

 

 

 

Maximum Attenuation 

0 to 10 dB. This control determines the maximum amount of attenuation that 

the ALC and the LTLC algorithm can apply. This is to prevent over adjustment 

which can lead to unwanted audio artefacts. 

 

 

 

 

Preset 

Subtle, Standard, Strong. The available options are Subtle, Standard and 

Strong. This setting controls the aggressiveness of the corrections performed 

by the Short Term ALC algorithm. It controls how quickly the correction takes 

place and the strength of the correction. 

 

 

 

 

Reset Statistics 

True, false. This can be used to reset the statistics that have been collected in 

the Audio Algorithm. Due to the slower update nature of the web interface the 

apparent change would be to the measurement of the Integrated Loudness 

only. 

 

 

 

Advanced 

 

 

 

 

 

Lip Sync Offset 

-500 to 500 ms. Configures a delay to the audio to improve A/V 

synchronization. 

 

 

 

 

Gain 

-6 to 6dB. Sets the gain in dB for the audio stream. 

Summary of Contents for AVP 4000







































































































































































































































































































































































































































Reviews:

No comments