manualshive.com logo in svg

Ericsson AVP 4000, Reference Manual, Page: 220 / 422

Share
Download
Ericsson AVP 4000 Reference Manual Download Page 220

 

 

Web GUI Control  

 

5-36 

 

1/1553-FGC 101 1790 

Uen

 Y

  

 

 

 

Parameter 

Values 

Description 

VBI Line 6 - VBI Line 

22 

Off, VITS, WSS, WSS-AFD, Teletext System B, 

Monochrome Samples 

Specifies the content in the respective VBI lines. Set to Off 

if the line in the incoming video does not carry any 

information, VITC for Time Code, WSS for Wide Screen 

Signaling, WSS-AFD for Active Format Detection and 

Teletext System B for Teletext. Visible for 576i (625-line) 

input streams. 

VBI Line 23 

Off, WSS, WSS-AFD 

Specifies the content of VBI line 23 for 576i (625 line) input 

streams. 

Field 2

 

VBI Line 272 - VBI 

Line 285 

Off, VITC, Closed Captions, Monochrome 

Samples 

Specifies the content in the respective VBI lines. Set to Off 

if the line in the incoming video does not carry any 

information, Closed Caption for closed caption information. 

Visible for 480i (525-line) input streams. 

VBI Line 318 - VBI 

Line 335 

Off, VITS, WSS, WSS-AFD, Teletext System B, 

Monochrome Samples 

Specifies the content in the respective VBI lines. Set to Off 

if the line in the incoming video does not carry any 

information, VITC for Time Code, WSS for Wide Screen 

Signaling, WSS-AFD for Active Format Detection and 

Teletext System B for Teletext. 

Aspect Ratio Conversion 

The following parameters are available on the 

ARC

 tab of the 

Properties

 widget on the 

Service Configuration

 page when a video stream is selected on the 

Outputs

 widget. The 

same parameters can be accessed through the 

Advanced/EI9001/Video/Input/Video 

Aspect Ratio (AR) Conversion

 menu on the front panel.

 

Table 5.7  Aspect Ratio Parameters 

Parameter 

Values 

Description 

Use Input AFD 

Off, On 

If set to On, AFD codes present on the input will be used 

to control the aspect ratio conversion. 
If set to Off, the Default Aspect Ratio Conversion will 

always be used. 

Default Aspect Ratio 

Conversion 

Anamorphic, Center Cut, Letterbox 

Specifies what aspect ratio conversion will be done if not 

using the AFD codes present on the input. 

Video Index

1

 

Off, On (Default), On (User) 

 

Video Index Field 1

1

 

6 to 22

2 

10 to 22

3

 

Specifies which line contains the video index in field 1. 

Video Index Field 2

1

 

319 to 335

2

 

272 to 285

3

 

Specifies which line contains the video index in field 2. 

SMPTE 2016 

Off, On 

 

Default Input Aspect 

Ratio 

4:3, 16:9 

 

WSS-AFD 

Configure using VBI lines section 

Read-only, informative text. 

Action on AFD lost 

Convert as anamorphic and put AFD code 1000 

out. 
Convert as specified in Default and put AFD 

code out. 

Specifies what aspect ratio conversion is performed when 

AFD is not present on the input 

Summary of Contents for AVP 4000







































































































































































































































































































































































































































Reviews:

No comments