manualshive.com logo in svg

Ericsson AVP 4000, Reference Manual, Page: 157 / 422

Share
Download
Ericsson AVP 4000 Reference Manual Download Page 157

 

Front Panel Control 

 

 

1/1553-FGC 101 1790 Uen Y

 

 

4-17 

 

 

 

 

Telephone Number 

Enables entry/editing of a telephone number. 

 

Telephone Extension 

Enables entry/editing of a telephone number. 

 

Latitude 

Enables selection of latitude. 

 

Longitude 

Enables selection of longitude. 

 

User Information 

Enables entry of user information. 

 

NIT Descriptor Tag 

Enables entry/editing of a NIT descriptor tag. 

USB Control

1

 

 

 

Format USB Stick 

Recreates the default directory structure on the USB stick connected to the front panel. 

1 Visible only when a USB drive is detected. 

4.4.2 

Advanced Menu 

The 

Advanced

 menu allows access to all of the 

Advanced

 menus for the installed 

option cards. Selecting the option card (the parameters of which you wish to edit) 

from the 

Slot <n>

 option will give access to the required menu. 

If no option card is selected, the System menu is displayed as shown below. 

Table 4.8  Advanced Menu 

Advanced 

Slot <n> 

See the menu of the installed card: 

EI9001 Encoder / EI9001T Transcoder Advanced Menu 

  

External Sync Input Card

 

ASI Option Card Advanced Menu

 

System 

 

 

Network Configuration 

 

 

 

Check Duplicate IP Address 

Enable, Disable. If enabled, the unit checks whether there is another unit with the same 

IP address within the network by sending out ARP messages. 

 

 

Control Interface Group 

 

 

 

 

Network Mode 

Same-Network, Different-Network. Read only parameter for the control interface, and is 

set to Same-Network. 

 

 

 

IP Redundancy Mode 

Active-Active, Active-Standby. Describes how the spare interfaces will behave. For the 

control port, it is set to Active-Standby and is read only. 

 

 

 

Autorevert 

Auto-revert to Primary, Auto-revert to Secondary. Shown only if the 

IP Redundancy 

mode

 is set to Active-Standby. Determines what to do when connection is lost. 

 

 

 

Autorevert Delay 

The delay in seconds before automatic redundancy switching takes place. Shown only if 

the 

IP Redundancy mode

 is set to Active-Standby. 

 

 

 

Active Interface 

Read only parameter. Displays which interface is active. In Active -Active redundancy 

mode both interfaces are active. 

 

 

 

Line Speed 

Auto, 100 Mbps, 1 Gbps. The transmission speed of the link. 

 

 

 

Duplex Mode 

Auto, Full Duplex, Half Duplex. Determines whether data should be transmitted and 

Summary of Contents for AVP 4000







































































































































































































































































































































































































































Reviews:

No comments