manualshive.com logo in svg

Ericsson AVP 4000, Reference Manual, Page: 217 / 422

Share
Download
Ericsson AVP 4000 Reference Manual Download Page 217

 

Web GUI Control    

 

 

1/1553-FGC 101 1790 

Uen

 Y

 

 

5-33 

 

 

 

5.5.3.1 

EI9001 and EI9001T 

5.5.3.1.1 

Video and VBI Stream Configuration 

Video Input 

The following parameters are available on the 

Input

 tab of the 

Properties

 widget on 

the 

Service Configuration

 page when a video component is selected in the 

Outputs

 widget. The same parameters can be accessed through the front panel 

menus. 

Table 5.5  Video Input Parameters 

Parameter 

Values 

Description 

Video Input Lock 

Yes, No 

Shows whether there is a video lock to the format specified 

through the parameters below. Read only parameter. 

Source 

SDI 

The video will be sourced from the SDI/HD-SDI input on 

the rear panel. 

Daughter Card (i.e. IP input to the Transcoder) 

The input Transport Stream to the chassis, via IP, is routed 

to the Transcoder Card

1

. 

VCM in slot (N-1) 

It is possible to use the input presented to the card to also 

be used on the card in the next higher slot number. 

Color Bars 

An internally generated color bars test pattern will be used 

as the video source. 

Black 

An internally generated black test pattern will be used as 

the video source. 

Moving Object 

An internally generated moving object test pattern will be 

used as the video source. 

Slate 

The full Slate uploaded by the user will be used as the 

video source. 

HD Auto Input 

Detection 

Off, HD 25/50Hz, HD 29.97/59.94Hz 

Automatic detection and configuration of video encoding 

according to the incoming video format for HD video only. 
For incoming SD video, select Off. 

Detected Video 

Format 

HD 1080i25, HD 720p50, HD 1080i29.97, HD 

720p59.94 

Shows the video format of incoming video as detected by 

the AVP 4000. Read only parameter and only present if 

HD Auto Input Detection is active. 

Video Input Format 

SD 567i25, SD 480i29.97, HD 720p50, HD 

720p59.94, HD 1080i25, HD 1080i29.97 

Defines the expected video format on the SDI input or the 

video format used for encoding the test patterns. A change 

in the Video Input Format might result in a change in the 

Video Profile used for encoding.  

Display Slate after 

Sensitivity Delay 

Off, On 

Disables or enables delayed action upon Video Input Lock 

Loss (see first entry above). The delayed action is always 

to display a slate, which must have been loaded (see Slate 

File entry below). The immediate action is that defined 

below in Output on Video Loss, but Freeze Frame is 

recommended when using the delayed slate display. 

Sensitivity Delay 

3 to 60 seconds 

Only present if the parameter above is set to On. Video 

input lock must have been lost for approximately that 

duration before the slate is automatically displayed. The 

same delay is applied when regaining lock before 

removing the slate. 

Output On Video Loss 

Freeze Frame 

Repeats the last good video frame on loss of video input. 

Summary of Contents for AVP 4000







































































































































































































































































































































































































































Reviews:

No comments