Ericsson AVP 4000 Reference Manual Download Page 270

Page: 270 / 422

Web GUI Control

5-86

1/1553-FGC 101 1790

Uen

Non Block Aligned linearization is dealt with in Annex A of the ProMPEG Code of

Practice. In Non Block Aligned the matrix is ‘skewed’ for the column calculation. The

L column FEC packets are played out at the end of every column plus a constant.

For ‘square’ matrices (diamonds) where

then these column packets will

emerge at regular intervals. For ‘rectangular’ diamonds they will not. In the case of a

4 column by 20 row matrix the 4 FEC packets will emerge within 16 slots, followed

by a gap of 64 slots before the next 4. It therefore produces a less linear spread of

packets.

Receivers which do not have FEC capability can simply ignore the FEC packets and

just make use of the media packets.

5.5.4.5

VLAN Tagging

VLAN tagging can be used to segregate IP packets from data interfaces.

5.5.4.5.1

VLAN Creation

A VLAN is created by specifying the VLAN ID, IP address and the Netmask. All

Transport Streams which are tagged to this VLAN use the VLAN IP address as its

source IP address. Hence the VLAN and VLAN ID must be created before it can be

used to tag a Transport Stream.

To create VLANs, on the

Advanced Setup

tab of

Device Configuration

page

navigate to the

Encoder > Vlan Tags

folder, select the output you want to assign

the VLAN tag to, and click

Add

in the

Properties

pane. Alternatively, on the front

panel navigate to

Advanced/System/Vlan Tags

and set up the VLANs as required.

The available options are listed in the following table.

Table 5.65 VLAN Creation Options

Parameter

Values

Description

Vlan ID (Create)

2-4094

New VLAN ID to create.

Vlan IP

xxx.xxx.xxx.xxx

VLAN IP Address (VLAN tagged Transport Stream will have this as

its source IP address).

Vlan Netmask

yyy.yyy.yyy.yyy

VLAN Netmask.

Vlan Gateway

zzz.zzz.zzz.zzz

VLAN gateway address for the current VLAN.

Note:

The VLAN Id and its IP address must be unique across all Ethernet

interfaces.

VLAN Tag Sharing

Once the VLANs are created, they can be assigned to IP Transport Streams. To do

that, navigate to

Service Configuration

page, and create a Transport Stream for

the appropriate IP output. Then, click on the newly created Transport Stream, and in

the

Properties

widget select the required VLAN tag. VLANs can also be assigned to

Transport Streams in the

Outputs/IP Output <m>/Data Interface Group

<n>/Transport Stream ID: <id>/Destination List/Destination <k>/Vlan Tag

front

panel menu. The following options can be set:

Summary of Contents for AVP 4000







































































































































































































































































































































































































































Search results

Summary of Contents for AVP 4000

Reviews:

Ericsson AVP 4000, Reference Manual, Page: 270 / 422

Search results

Summary of Contents for AVP 4000

Reviews: