Ericsson AVP 4000 Reference Manual Download Page 152

Page: 152 / 422

Front Panel Control

4-12

1/1553-FGC 101 1790 Uen Y

Bit Rate Weighting

Fixed, Minimum, 2-20. The weighting associated to the current

component. A component with Fixed weighting does not respond to

changes in the Transport Stream Bit Rate. If Minimum is set for a

component, it will always use the minimum Bit Rate defined for the

video profile it is encoded with. A value 2-20 determines how much

a component is changed when the Transport Stream Bit Rate is

changed relative to other components with Bit Rate weighting other

than Minimum.

Master TS

Information only – master TS for Bit rate tracking

Service ID

The unique identifier of the current service within the current

Transport Stream.

PMT PID

PID assigned to the PMT that describes the current service.

PCR PID

The PID of the TS packets that carry the clock reference for the

current service. If the service has a component with the Embedded

PCR parameter set to On, this field contains the PID of that

particular video stream and it is read only.

SDT Parameters

Service Provider

The name of the service provider as appears in the NIT.

Service Name

The name of the service as appears in the NIT.

Service Type

Digital TV, Digital Radio, Teletext, Mosaic, Data Broadcast.

BISS Key

Security key for Basic Interoperable Scrambling System (BISS).

NIT Service Parameters

LCN

0 - 1023

Current State

The Setmode state of the Transport Stream. Read only parameter.

Change State

Sets the Setmode state of the Transport Stream. The options

available depends on the value set for MGP Mode under

Advanced/System/MGP Support.

Transport Stream Bit Rate

The Bit Rate of the Transport Stream.

Reserved Bit Rate

The Bit Rate of the ???.

Bit Rate Tracking Mode

Off, Maximise video. Enables or disables Bit Rate tracking for the

current Transport Stream.

Auto Enable

If set to true, it automatically re-enables the Transport Streams

when all the specified error conditions are cleared.

Auto Disable

Never, Audio Lost, Video Lost, Any Upstream CRITICAL Alarm, Any

CRITICAL alarm. Disables the output when the set condition is met.

The Transport Stream can be set to be re-enabled at the Auto

Enable option.

Syntax

DVB, ATSC

Program Specific Information

Transport Stream ID

A new ID can be assigned to the Transport Stream.

PAT-PMT

On, Off

PAT-PMT Parameters

Summary of Contents for AVP 4000







































































































































































































































































































































































































































Search results

Summary of Contents for AVP 4000

Reviews:

Ericsson AVP 4000, Reference Manual, Page: 152 / 422

Search results

Summary of Contents for AVP 4000

Reviews: