Ericsson AVP 4000 Reference Manual Download Page 348

Page: 348 / 422

Glossary

A-2

1/1553-FGC 101 1790 Uen Y

ALC

Automatic Loudness Control: ALC is an audio processing mode for

measuring and modifying audio amplitude with the aim of changing

the perceived loudness level. It uses a measurement based upon

the new standards for measuring audio loudness defined in ITU-R

BS.1770-2, this standard forms the measurement basis of the

guidelines in EBU R128 and ATSC/A85.

AMOL I and II

Automatic Measure of Line-ups I and II: Used by automated

equipment to measure programme-viewing ratings.

ARP

Address Resolution Protocol. A protocol used to "resolve" IP

addresses into underlying Ethernet MAC addresses.

ASI

Asynchronous Serial Interface.

ASIC

Application-Specific Integrated Circuit: A customized chip designed

to perform a specific function.

Async

Asynchronous.

ATM

Asynchronous Transfer Mode: A connection orientated, cell based,

data transport technology designed for Broadband ISDN (B-ISDN).

It provides a circuit-switched bandwidth-on-demand carrier system,

with the flexibility of packet switching. It offers low end-to-end delays

and (negotiable on call set up) Quality of Service guarantees.

Asynchronous refers to the sporadic nature of the data being

transmitted. Cells are transmitted only when data is to be sent,

therefore the time interval between cells varies according to the

availability of data.

ATSC

Advanced Television Standards Committee: An organization

founded in 1983 to research and develop a digital TV standard for

the U.S.A. In late 1996, the FCC adopted the ATSC standard, the

digital counterpart of the NTSC standard.

AVC

Advanced Video Coding - see MPEG-4.

AVP

Advanced Video Processor.

B3ZS

Bipolar with Three Zero Substitution: A method of eliminating long

zero strings in a transmission. It is used to ensure a sufficient

number of transitions to maintain system synchronization when the

user data stream contains an insufficient number of 1s to do so.

B3ZS is the North American equivalent of the European HDB3.

Backward

Compatibility

Refers to hardware or software that is compatible with earlier

versions.

BAT

Bouquet Association Table: Part of the service information data. The

BAT provides information about bouquets. It gives the name of the

bouquet and a list of associated services.

baud rate

The rate of transfer of digital data when the data comprises

information symbols that may consist of a number of possible states.

Equivalent to bit rate when the symbols only have two states (1 and

0). Measured in Baud.

Summary of Contents for AVP 4000







































































































































































































































































































































































































































Search results

Summary of Contents for AVP 4000

Reviews:

Ericsson AVP 4000, Reference Manual, Page: 348 / 422

Search results

Summary of Contents for AVP 4000

Reviews: