Ericsson AVP 4000 Reference Manual Download Page 403

Page: 403 / 422

Alarm Lists

1/1553-FGC 101 1790 Uen X

D-13

Alarm

Description

Port Number

Alarm ID

Source

Severity

Audio 2 ADS silence

Silent period detected. Valid only for

Audio Description Service encoding.

03122029

Audio 2

minor

Audio 2 Clipping

Audio output is clipping. Audio gain

value or input amplitude should be

reduced.

0312202A

Audio 2

minor

Audio 2 VPS/ARIB Coding Mode

Mismatch

The coding mode signalled by

VPS/ARIB is not supported by the

current Audio Codec

0312202B

Audio 2

minor

Audio 3 Input lock

No valid audio detected on selected

input. Please check source

connection.

03122040

Audio 3

major

Audio 3 TS input error

Incoming transport stream error.

Please check source TS.

03122041

Audio 3

major

Audio 3 Compressed audio not

detected

Compressed audio not detected on

input. Please check source

connection and source format.

03122042

Audio 3

minor

Audio 3 Input frame CRC failure

CRC error in compressed input

frame. Output is muted.

03122043

Audio 3

minor

Audio 3 Unsupported sample

rate

Unsupported sample rate at decoder

output.

03122044

Audio 3

minor

Audio 3 Dolby E program not

present

Program not present in Dolby E

stream.

03122045

Audio 3

minor

Audio 3 Dolby E alignment

Dolby E frames not properly aligned

to video frames. May glitch on frame

drop/repeat and video may not be

aligned to audio.

03122046

Audio 3

minor

Audio 3 Dolby E metadata frame

rate mismatch

Frame rate indicated in Dolby E

metadata does not match current

video frame rate.

03122047

Audio 3

minor

Audio 3 ADS control track

Control track for audio description

not present.

03122048

Audio 3

minor

Audio 3 ADS silence

Silent period detected. Valid only for

Audio Description Service encoding.

03122049

Audio 3

minor

Audio 3 Clipping

Audio output is clipping. Audio gain

value or input amplitude should be

reduced.

0312204A

Audio 3

minor

Audio 3 VPS/ARIB Coding Mode

Mismatch

The coding mode signalled by

VPS/ARIB is not supported by the

current Audio Codec

0312204B

Audio 3

minor

Audio 4 Input lock

No valid audio detected on selected

input. Please check source

connection.

03122060

Audio 4

major

Audio 4 TS input error

Incoming transport stream error.

Please check source TS.

03122061

Audio 4

major

Audio 4 Compressed audio not

detected

Compressed audio not detected on

input. Please check source

connection and source format.

03122062

Audio 4

minor

Audio 4 Input frame CRC failure

CRC error in compressed input

frame. Output is muted.

03122063

Audio 4

minor

Summary of Contents for AVP 4000







































































































































































































































































































































































































































Search results

Summary of Contents for AVP 4000

Reviews:

Ericsson AVP 4000, Reference Manual, Page: 403 / 422

Search results

Summary of Contents for AVP 4000

Reviews: