manualshive.com logo in svg

Ericsson AVP 4000, Reference Manual, Page: 159 / 422

Share
Download
Ericsson AVP 4000 Reference Manual Download Page 159

 

Front Panel Control 

 

 

1/1553-FGC 101 1790 Uen Y

 

 

4-19 

 

 

 

 

 

 

 

Link Status 

Link Down, Link Up. The status of the current physical data interface. Read only 

parameter. 

 

 

 

 

Link Up Time 

The time in days, hours, minutes and seconds the link is established. Read only 

parameter. 

 

 

 

 

TX Packets 

Packets transmitted since the link is up. Read only parameter. 

 

 

 

 

RX Packets 

Packets received since the link is up. Read only parameter. 

 

 

 

 

IP Address 

The IP address of the physical data interface. 

 

Model 

 

 

 

Build Version 

 

 

 

 

Assembly Date 

The time and date when the current unit was assembled. Read only parameter. 

 

 

 

Software Version 

The version of the software currently installed on the unit. Read only parameter. 

 

 

 

Serial Number 

The serial number of the unit. Read only parameter. 

 

 

Chassis Type 

The type of the chassis. Read only parameter. 

 

 

PSU A Option 

The voltage level provided by PSU A. Read only parameter. 

 

 

PSU B Option 

The voltage level provided by PSU B. Read only parameter. 

 

 

Inlet A 

AC, DC, none. The type of the power through inlet A of the current unit. Read only 

parameter. 

 

 

Inlet B 

AC, DC, none. The type of the power supply through inlet B of the current unit. Read 

only parameter. 

 

 

Inlet Mode 

Supply mode of the inlets. Read only parameter. 

 

 

Number of Usable Slots 

The number of slots in the current unit. Single PSU units have 6 slots, dual PSU units 

have 4 or 6 slots. Read only parameter. 

 

Base Unit 

 

 

 

Build Version 

 

 

 

 

Host Controller Card Id 

The Card Id of the host controller card. Read only parameter. 

 

 

 

Software Date 

The date the host software was compiled. Read only parameter. 

 

 

 

Software Version 

The version of the software running on the host controller card. Read only parameter. 

 

 

 

Hardware Version 

The hardware version of the host controller card. Read only parameter. 

 

 

 

Backplane Version 

The backplane version of the host controller card. Read only parameter. 

 

 

 

S Number 

The BOM assembly number of the host card. The S number specifies the available 

software and firmware features of the card. Read only parameter. 

 

 

 

Serial Number 

The serial number of the host card. Read only parameter. 

 

 

 

Software/Firmware 

 

 

 

 

 

BSP Software Version 

The software version of the board support package. Read only parameter. 

 

 

 

 

Application Software 

Version 

The version of the application that runs on the host controller card. Read only 

parameter. 

 

 

 

 

Boot FPGA Firmware 

The firmware version of the boot FPGA. Read only parameter. 

Summary of Contents for AVP 4000







































































































































































































































































































































































































































Reviews:

No comments